background image

vii

 

ATTO Technology Inc. FibreBridge Installation and Operation Manual

SASQSFPInfo

Reports information about the SAS QSFP.

get SASQSFPinfo [a 

|

 b | all]

SASTargets

Lists the physical devices that are connected to all SAS 
connectors and PHYs.

SASTargets

SaveConfiguration

Many commands require a 

SaveConfiguration

 command to 

be executed as indicated by the return 

Ready. *

. When you 

invoke a 

SaveConfiguration 

command, the current 

configuration is permanently saved in the FibreBridge and the 
new configuration becomes the active configuration. If a 
firmware restart is required to make the requested change 
permanent, you are asked to confirm the restart. You can 
override this request by indicating the override value on the 
command line. You may make several changes through 
commands before implementing the restart, but once you have 
restarted the FibreBridge, all the command changes created 
before the restart and save are implemented. If you select the 
restart option, the FibreBridge executes its complete start up 
cycle.

SaveConfiguration <Restart | NoRestart>

SerialNumber

Reports the FibreBridge serial number. The serial number, 
unique for each FibreBridge, is a 13-character field. The first 
seven alphanumeric characters are an abbreviation of the 
product name while the remaining six numbers are the 
individual FibreBridge board’s number. 

get SerialNumber

SerialPortBaudRate

Configures/reports the baud rate for the FibreBridge RS-232 
serial port or header. The number of data bits per character is 
fixed at 8 with no parity. 

Default: 115200
set SerialPortBaudRate [ 9600 |19200 | 38400 | 57600 | 

115200]

Requires a SaveConfiguration Restart command
get SerialPortBaudRate

SNTP

Controls whether the FibreBridge contacts a specified SNTP 
time server to initialize or synchronize the time.

Default: enabled
set SNTP [enabled | disabled]
Requires a SaveConfiguration Restart command
get SNTP

SNTPServer

Controls/displays the main IP address of the SNTP time server. 
If the FibreBridge is unable to contact the specified SNTP time 
server within 30 seconds, the FibreBridge tries to contact the 
first auxiliary SNTP time server. If not successful, the 
FibreBridge tries to contact the second auxiliary server. If not 
successful, the FibreBridge continues to keep time based on the 
most recent SNTP time server, physical RTC or manual 
initialization or synchronization.

Default: 192.43.244.18
set SNTPServer xxx.xxx.xxx.xxx
Requires a SaveConfiguration Restart command
get SNTPServer

Temperature

Displays the current internal temperature of the FibreBridge in 
degrees Celsius.

get Temperature

Time

Controls/displays the time in a 24-hour format. The default time 
is 00:00:00 and is accurate until the FibreBridge is reset or 
power-cycled when it returns to the default.

Time

 cannot be set 

if 

SNTP

 is enabled.

Default: 0:00:00
set Time [HH :MM :SS]
Requires a SaveConfiguration command
get Time

TimeZone

Controls/displays the time zone. Setting may be 

EST, CST, 

MST PST

 or a numerical offset from GMT in the format 

+/- 

HH:MM

. When 

SNTP

 is enabled, applies the time zone setting 

to the time retrieved from a specified SNTP time server to 
determine local time. 

Default: EST
set TimeZone [EST | CST | MST | PST | [+ / - HH : MM]]
Requires a SaveConfiguration command
get TimeZone

Username

Specifies user name for all Telnet, FTP and ExpressNAV user 
management console sessions. 

Username

 is case 

insensitive, 1-32 characters, no spaces.

Default: root
set Username 
Requires a SaveConfiguration command
get Username

Содержание FibreBridge 6500N



























Отзывы: