ATTO Technology FibreBridge 4500C, Инструкция по установке и эксплуатации

Страница: 14 / 65

7
ATTO Technology FibreBridge 4500 Installation and Operation Manual
2.2 ATTO FibreBridge 4500R/D characteristics
The ATTO FibreBridge 4500R/D is a Fibre Channel to SCSI bridge for high throughput enterprise environments
designed for mission-critical applications which can be used on a desktop or in a rack.
The FibreBridge 4500R/D is a versatile enclosure with
attached feet for horizontal desktop use and mounting
brackets to convert to standard 19-inch enclosures. All
cable connections and the power switch are on one
outer panel (which may be considered the front or the
back of the bridge depending on your needs) while
LED indicators are on both outer panels.
Dimensions
Width:
16.725 inches (424.5 mm.)
Depth:
10 inches (253.8 mm)
Height:
1.72 inches (43.7 mm).
Weight:
10 pounds
Cooling and airflow
Temperature:
5-50
o
C
Humidity: 0-90% non-condensing
Ambient air
should not exceed 50
o
C.
Air enters from the front and is exhausted out the
connector side by a blower inside the enclosure which
provides 11 cubic feet per minute of airflow.
WARNING Do not block the enclosure’s vents. The
FibreBridge will shut down if overheating occurs.
Power
The power supply circuit is permanently mounted
within the enclosure and is not hot swappable. It has
one standard IEC320 power receptacle and switch.
The universal power supply provides power for the
bridge board and cooling fans.
Input voltage
110/230V AC, with operating input
range of 90-132V AC or 175-264V AC, 47-63Hz,
single phase. The AC input range selection is
automatic with no manual or jumper switchover
required.
Output voltage
+12V at 0.4 amps, +5 at 3.0 amps,
+3.3V at 7 amps.
Power draw
2 amps at 110V.
Fibre Channel ports
Each Fibre Channel port can connect the FibreBridge
to either a Fabric or Arbitrated Loop.
➔
1.0625 gigahertz (100 MB/sec.)
➔
Class 2, Class 3 and ANSI Fibre Channel
specifications support
➔
PLDA, Public Loop Login (NL_port) and Fabric
Direct Connect (N_port) support
➔
Full Duplex transmission support
➔
Fixed optical short wave connectors
SCSI ports
The four SCSI ports on the FibreBridge 4500 connect
storage devices into the Fibre Channel Storage Area
Network (SAN). Each port is totally independent.
A FibreBridge can be ordered with either of the
following SCSI ports:
Ultra 2 (LVD) SCSI
80 MB/sec. max per bus, downward
compatible with all forms of single-ended SCSI
High Voltage Differential (HVD) Ultra SCSI
40 MB/sec.
max per bus
Ethernet port
The 10/100 Base T Ethernet port supports FTP-,
SNMP- and Telnet-based monitoring and
management.
Serial port
The RS-232 serial port provides support for remote
monitoring and management.
Reset button
The reset button near the LED indicators on the
connector side of the FibreBridge will restart the
FibreBridge.
LED indicators
FC 0 Activity, FC 1 Activity, FC 2 Activity
each LED
blinks to show activity on the Fibre Channel port
(numbered 0, 1 and 2). During very high activity, the
LEDs appear to be steadily lit.
SCSI 0 Activity, SCSI 1 Activity, SCSI 2 Activity, SCSI 3
Activity
each SCSI bus has its own LED to show
activity on that bus (numbered 0, 1, 2, 3).
Ready
should light after the FibreBridge has passed its
internal self diagnostic test, indicating the FibreBridge
is ready to operate.
Fault
indicates if there is a problem with the
FibreBridge. If the fault LED blinks in a consistent
pattern, contact ATTO Technology Technical Support.