ATN Zebra 12, Руководство оператора и по безопасности

Страница: 35 / 45

OPERATOR AND SAFETY MANUAL
1NO0027UK-05
ZEBRA 12
35
REP DESCRIPTION QTY TYPE COMMENT J 50H 150H 300H 600H 1200H
5 Hydraulic oil tank 1 H46 Check level X
11 Engine oil 1 15W40 Check level X
11 Engine oil filter 1 15W40 Drain + change X X
6 Hydraulic oil return filter 1 H46 Change X X
7 Hydraulic oil pressure filter 1 H46 Change X X
5 Hydraulic oil tank 1 H46 Drain + level X X
1 Hydraulic reducers 4 80W90 Drain + level X X
14 Telescope 1 GR Greasing on pad span X X
1 Hydraulic reducers 4 80W90 Check level X X
12 Engine air filter 1 - Clean X X
10 Diesel fuel filter 1 D Clean decanter bowl X X
2 Steering pivot geasers 4 GR Apply grease pump X
3 Bar joint + steering jack greasers 3 GR Apply grease pump X
4 Jack axis greasers 13 GR Apply grease pump X
15 Orientation crown gear greasers 4 GR Apply grease pump X
13 Joint axis greasers 16 GR Apply grease pump X
10 Diesel fuel filter 1 D Change X
9 Diesel fuel pre-filter 1 D Change X
12 Engine air filter 1 - Change X
8 Diesel fuel tank 1 D Drain + clean X
REP DESCRIPTION QTY TYPE COMMENT J 50H 150H 300H 600H 1200H
5 Hydraulic oil tank 1 H46 Check level X
11 Engine oil 1 15W40 Check level X
11 Engine oil filter 1 15W40 Drain + change X X
6 Hydraulic oil return filter 1 H46 Change X X
7 Hydraulic oil pressure filter 1 H46 Change X X
5 Hydraulic oil tank 1 H46 Drain + level X X
1 Hydraulic reducers 4 80W90 Drain + level X X
14 Telescope 1 GR Greasing on pad span X X
1 Hydraulic reducers 4 80W90 Check level X X
12 Engine air filter 1 - Clean X X
10 Diesel fuel filter 1 D Clean decanter bowl X X
2 Steering pivot geasers 4 GR Apply grease pump X
3 Bar joint + steering jack greasers 3 GR Apply grease pump X
4 Jack axis greasers 13 GR Apply grease pump X
15 Orientation crown gear greasers 4 GR Apply grease pump X
13 Joint axis greasers 16 GR Apply grease pump X
10 Diesel fuel filter 1 D Change X
9 Diesel fuel pre-filter 1 D Change X
12 Engine air filter 1 - Change X
8 Diesel fuel tank 1 D Drain + clean X
5.7. WHEELS
Proper maintenance of the wheels extends their lifetime. Always
check for wear or tear, as if a wheel breaks, this may cause
severe or lethal injuries.
The wheel nuts must be tightened at proper torque, i.e. using a
torque wrench.
Fit and approach all nuts by hand to avoid damaging the thread:
do not grease the wheel nuts.
Tighten the nuts in the sequence indicated
here, while tightening at the torque specified in
3 phases:
Check the tightening torque at the first 50 hours maintenance, then every 150 hours.
- NOTE-
Checking inflating pressure is not necessary as the wheels are solid, hence puncture-proof.
5.8. STARTING BATTERY
The current in the electric system is 12 volts. The starting battery is also used to supply the
emergency hydraulic plant. Therefore, the battery must be maintained charged at all times,
especially in cold weather.
CLEANING THE BATTERY
PHASE 1 PHASE 2 PHASE 3
60Nm 135Nm 270Nm
WHEEL NUT TIGHTENING TORQUE