Atmel AVR2052 Скачать руководство пользователя страница 54

Страница: 54 / 67

Atmel AVR2052

8200M-AVR-11/11

13 Appendix A-7: SAM3S specifics

13.1 Getting started

The Atmel BitCloud SDK supports two different hardware platforms with SAM3S

microcontrollers: Atmel SAM3S-EK with radio boards from the RZ600 kit, and Atmel

RF231USB-RD. The instructions below highlight the differences between the two

platform configurations, where present.

13.1.1 Required hardware

Before installing and using the Atmel BitCloud SDK, make sure that all necessary

hardware is available for the kit you would like to use:

•

For SAM3S-EK:

Two or more SAM3S-EK boards

Atmel RZ600 radio board with

AT86RF230, AT86RF231 or

AT86RF212 transceiver –

for each SAM3S-EK board

Atmel AT91SAM-ICE JTAG emulator

•

For RF231USB-RD:

Two or more RF231USB boards

Atmel AT91SAM-ICE JTAG emulator

13.1.2 Hardware setup

•

For SAM3S-EK, connect the RZ600 radio board transceiver to the J16/ZigBee

connector present on the SAM3S-EK board.
For other hardware setup instructions, please refer to

[29]

•

For RF231USB-RD hardware instructions, please refer to

[36]

13.1.3 System requirements

Before using the SDK, please ensure that the following system requirements are met

by your PC and development environment.

Table 13-1.

System requirements for SAM3S-EK.

Parameter

Value

Note

CPU

Intel Pentium III, or higher,

800MHz

RAM

128MB

Free space on hard disk

50MB

JTAG emulator

AT91SAM-ICE emulator with

cable

Required to upload firmware

onto the boards and debug

through JTAG

Operating system

Windows 2000/XP

Содержание AVR2052




































































Результаты поиска

Содержание AVR2052

Отзывы:

Похожие инструкции для AVR2052

Бренды по названию

Популярные бренды

Atmel AVR2052, Быстрый старт

Результаты поиска

Содержание AVR2052

Отзывы:

Похожие инструкции для AVR2052

Бренды по названию

Популярные бренды