Atmel AVR XMEGA AU series Скачать руководство пользователя страница 254 | Manualshive

Страница: 254 / 512

background image

254

8331B–AVR–03/12

Atmel AVR XMEGA AU

• Bit 7:2 – Reserved

These bits are unused and reserved for future use. For compatibility with future devices, always
write these bits to zero when this register is written.

• Bit 1 – TRNIF: Transaction Complete Interrupt Flag

This flag is when there is a pending packet interrupt in the FIFO.

• Bit 0 – SETUPIF: SETUP Transaction Complete Interrupt Flag

This flag is set when a SETUP transaction has completed successfully.

20.13.13 CALL – Calibration Low

CALL and CALH hold the 16-bit value, CAL. The USB PADs (D- and D+) are calibrated during
production to enable operation without requiring external components on the USB lines. The cal-
ibration value is stored in the signature row of the device, and must be read from there and
written to the CAL registers from software.

• Bit 7:0 – CAL[7:0]: PAD Calibration Low

This byte holds the eight lsbs of CAL.

20.13.14 CALH – Calibration High

• Bit 7:0 – CAL[15:8]: PAD Calibration High

This byte holds the eight msbs of CAL.

Bit

7

6

5

4

3

2

1

0

CAL[7:0]

CALL

Read/Write

R/W

R/W

R/W

R/W

R/W

R/W

R/W

R/W

Initial Value

0

0

0

0

0

0

0

0

Bit

7

6

5

4

3

2

1

0

CAL[15:8]

CALH

Read/Write

R/W

R/W

R/W

R/W

R/W

R/W

R/W

R/W

Initial Value

0

0

0

0

0

0

0

0

«
...
252
253
254
255
256
...
»

Содержание AVR XMEGA AU series

































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для AVR XMEGA AU series

ControlMaster CM15

Бренд: ABB Страницы: 4

Бренд: Fagor Страницы: 556

Бренд: Velleman Страницы: 12

Бренд: FuzzDog Страницы: 9

DMC-40x0 Series

Бренд: Galil Motion Control Страницы: 280

Бренд: Allen-Bradley Страницы: 88

Бренд: Levven Страницы: 2

Бренд: Samson Страницы: 44

Бренд: Beckhoff Страницы: 47

Бренд: DOTECH Страницы: 4

Бренд: MISUMI Страницы: 166

Бренд: Sunricher Страницы: 2

Бренд: KEPCO Страницы: 34

WB-150-IPW-1B-2

Бренд: watt box Страницы: 12

Goulds ResiBoost RB111512

Бренд: Xylem Страницы: 40

Бренд: WAREMA Страницы: 4

Бренд: Trio Страницы: 8

Бренд: Whelen Engineering Company Страницы: 10

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды