Atmel AVR XMEGA AU series Скачать руководство пользователя страница 212 | Manualshive

Страница: 212 / 512

background image

212

8331B–AVR–03/12

Atmel AVR XMEGA AU

16.7

Register Description

16.7.1

CTRL – Control register

• Bit 7:6 – Reserved

These bits are unused and reserved for future use. For compatibility with future devices, always
write these bits to zero when this register is written.

• Bit 5 – PGM: Pattern Generation Mode

Setting this bit enables the pattern generation mode. This will override the DTI, and the pattern
generation reuses the dead-time registers for storing the pattern.

• Bit 4 – CWCM: Common Waveform Channel Mode

If this bit is set, the CC channel A waveform output will be used as input for all the dead-time
generators. CC channel B, C, and D waveforms will be ignored.

• Bit 3:0 – DTICCxEN: Dead-Time Insertion CCx Enable

Setting these bits enables the dead-time generator for the corresponding CC channel. This will
override the timer/counter waveform outputs.

16.7.2

FDEMASK – Fault Detect Event Mask register

• Bit 7:0 – FDEVMASK[7:0]: Fault Detect Event Mask

These bits enable the corresponding event channel as a fault condition input source. Events
from all event channels will be ORed together, allowing multiple sources to be used for fault
detection at the same time. When a fault is detected, the fault detect flag (FDF) is set and the
fault detect action (FDACT) will be performed.

16.7.3

FDCTRL - Fault Detection Control register

Bit

7

6

5

4

3

2

1

0

–

–

PGM

CWCM

DTICCDEN

DTICCCEN

DTICCBEN

DTICCAEN

CTRL

Read/Write

R

R

R/W

R/W

R/W

R/W

R/W

R/W

Initial Value

0

0

0

0

0

0

0

0

Bit

7

6

5

4

3

2

1

0

FDEVMASK[7:0]

FDEMASK

Read/Write

R/W

R/W

R/W

R/W

R/W

R/W

R/W

R/W

Initial Value

0

0

0

0

0

0

0

0

Bit

7

6

5

4

3

2

1

0

–

–

–

FDDBD

–

FDMODE

FDACT[1:0]

FDCTRL

Read/Write

R

R

R

R/W

R

R/W

R/W

R/W

Initial Value

0

0

0

0

0

0

0

0

«
...
210
211
212
213
214
...
»

Содержание AVR XMEGA AU series

































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для AVR XMEGA AU series

Бренд: Garmin Страницы: 4

Бренд: National Instruments Страницы: 14

Бренд: National Instruments Страницы: 20

Бренд: Valcom Страницы: 3

Бренд: Valcom Страницы: 2

Бренд: YASKAWA Страницы: 121

Бренд: YASKAWA Страницы: 17

Бренд: YASKAWA Страницы: 30

Explorer Dongle

Бренд: Sparkfun Electronics Страницы: 16

CIMR-VC*****H**-00 series

Бренд: YASKAWA Страницы: 32

Бренд: Powtran Страницы: 40

PCI-to-IDE ATA-133

Бренд: Acard Страницы: 33

Бренд: RADEMACHER Страницы: 112

Бренд: Newport Страницы: 2

Бренд: VADDIO Страницы: 16

Бренд: Inca Страницы: 11

Бренд: AMALGAMATED INSTRUMENT Страницы: 45

Бренд: Viking Electronics Страницы: 12

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды