background image

15

Button Wiring Management

NOTE:

 In this step, we feed the button wiring into 

the lower compartment. This is just one option and 
this step is optional as you may mount the button 
in any location you choose.

Based on where you want to place the switch 
button, you may want to run the wiring through 
the cabinet. If you want to run the button wiring 
through the cabinet, complete the steps that 
follow.

7KHEXWWRQZRQȇWȴWWKURXJKWKHKROHLQWKH

backbox to the main body, so we need to 
temporarily remove the top portion of the 
button.

Pull up on the arm lock carefully and slide out the 
microswitch to the right.

Feed the microswitch and wiring through the hole 
in the bottom of the backbox down below to the 
main pinball body. Then, you can feed the wires 
forward through the body to the front of the 
pinball machine.

It is your choice where you want to mount the 
switch button. One idea is to feed it to the front 
of the machine, reattach the button, and then 
drill a hole through the bottom of the cabinet. 
Then, the player can reach under the table and 
click on the switch button when needed. Of 
course, you can also leave it all in the back of the 
pinball machine if you desire. Reconnect the 
button to the microswitch when you have placed 
the wiring in your desired location.

A

B

C

D

E

Содержание LEGENDS PINBALL


























Отзывы: