ATEN VM0808H Скачать руководство пользователя страница 34

Страница: 34 / 78

VM0808H User Manual

Operation Mode

The Power On Detection and EDID features are adjusted from the Operation
Mode menu.

The Power on Detection mode automatically switches an Output port
to the next powered-on source if its video source is powered off.

EDID (extended display identification data) is used to automatically or
manually setup different video configurations via EDID modes to
utilize the best resolution across different monitors.

To adjust the Power On Detection or EDID mode, from the Menu page, select
Operation Mode:

Power on Detection

To configure the VM0808H’s Power On Detection settings, do the following:

1. With the arrow on Power On Detection, press the OUT, IN, or ENTER

pushbutton to access the Power On Detection options.

2. Turn the front panel OUT/IN tuner dial to cycle through On or Off.

3. Press the OUT, IN, or ENTER pushbutton to confirm the change.

Operation Mode
Security Mode

ESC

ENTER

PROFILE

OUT

Power On Detection: ON
EDID: Default

ESC

ENTER

PROFILE

OUT

Содержание VM0808H















































































Результаты поиска

Содержание VM0808H

Отзывы:

Похожие инструкции для VM0808H

Бренды по названию

Популярные бренды

ATEN VM0808H, Руководство пользователя

Результаты поиска

Содержание VM0808H

Отзывы:

Похожие инструкции для VM0808H

Бренды по названию

Популярные бренды