ATEN VM0808H Скачать руководство пользователя страница 67

Страница: 67 / 78

Chapter 5. RS-232 Commands

Baud Rate Setting

You can select the RS-232 Baud Rate you want the VM0808H to use. Options
are 9600, 19200 (default) 38400 and 115200.

The formula for Baud Rate setting command is as follows:

Baud C Control [Enter]

For example, to select 38400 as your baud rate, type the following:

baud 38400 [enter]

The following tables show the possible values and formats for the

Control

command:

Note:

Each command string can be separated with a space.

The following table shows the available command list:

Command

Description

baud

Sets the RS-232 baud rate

Control

Description

9600

Use 9600 baud rate

19200

Use 19200 baud rate

38400

Use 38400 baud rate

115200

Use 115200 baud rate

Command

Control

Enter

Description

baud

9600 / 19200 / 38400 /

115200

[Enter]

Sets the RS-232 baud
rate

Содержание VM0808H















































































Результаты поиска

Содержание VM0808H

Отзывы:

Похожие инструкции для VM0808H

Бренды по названию

Популярные бренды

ATEN VM0808H, Руководство пользователя

Результаты поиска

Содержание VM0808H

Отзывы:

Похожие инструкции для VM0808H

Бренды по названию

Популярные бренды