Asus SP97-XV Скачать руководство пользователя страница 8 | Manualshive

Страница: 8 / 90

background image

8

ASUS SP97-XV User’s Manual

Features of the ASUS SP97-XV Motherboard

The ASUS SP97-XV motherboard is carefully designed for the demanding PC user
who wants many features in a small package, namely:

•

SiS Chipset: Features either SiS5582 or SiS5598 chipsets. The SiS5598 chipset
has a built-in video controller and supports video shared memory from 1-4MB.

•

Versatile Processor Support: Intel Pentium

®

75–233MHz (P55C-MMX

™

, P54C/

P54CS), IBM

®

/Cyrix

®

6x86-PR166+ (Rev 2.7 or later), IBM

®

/Cyrix

®

6x86MX

™

(PR166 & faster), AMD-K5

™

(PR75–PR133), AMD-K6

™

(PR166 & faster).

•

Versatile Memory Support: Is equipped with two DIMM sockets to support
8-128MB 168-pin 3.3Volt SDRAM/EDO memory modules up to 256MB. Is
also equipped with four SIMM sockets to support 4-64MB 72-pin Fast Page
Mode (FPM) or Extended Data Out (EDO) memory modules up to 256MB.
SIMMs and DIMMs cannot be used at the same time, damage may occur.

•

Easy Installation: Incorporates BIOS that supports autodetection of hard disk
drives, PS/2 mouse, and Plug and Play devices to make setup of hard disk drives,
expansion cards, and other devices virtually automatic.

•

ISA and PCI Expansion Slots: Provides four 16-bit ISA slots and four 32-bit
PCI slots

•

Super Multi-I/O: Provides two high-speed UART-compatible serial ports and
one parallel port with EPP and ECP capabilities.

•

Desktop Management Interface (DMI): Supports DMI through BIOS, which
allows hardware to communicate within a standard protocol creating a higher
level of compatibility. (Requires DMI-enabled components.) (See section V)

•

PCI Bus Master IDE Controller: Comes with an onboard Ultra DMA/33 Bus
Master IDE controller with two connectors. Supports four IDE devices more
than 8.4GB in two channels up to 33MB/sec IDE transfers and Enhanced IDE
devices. Also supports PIO Modes 3 and 4 and Bus Master IDE DMA Mode 2.
Includes integrated keyboard controller. Supports two of either 5.25- (360KB or
1.2KB) or 3.5-inch disk drives (720KB, 1.44MB, or 2.88MB). Supports Japa-
nese “Floppy 3 mode” (3.5-inch disk drive: 1.2MB) and LS-120 floppy disk
drives (3.5-inch disk drive: 120 MB, 1.44MB, 720K). BIOS supports IDE CD-
ROM or SCSI device bootup.

•

Level 2 Cache: Comes with onboard 512K Pipelined Burst SRAM.

•

IrDA Connector: Supports an optional infrared module for wireless interface.

•

Symbios SCSI BIOS: Supports optional ASUS SCSI controller cards through
onboard firmware.

•

Performance: 528MB/s data transfer rate using SDRAM, 33MB/s IDE transfer rate
using Bus Master UltraDMA/33 IDE, concurrent PCI allows multiple PCI transfers

•

Compliancy: ACPI ready for advanced power management features and PC’97
for greater support.

II. FEATURES

(Features)

II. FEA

TURES

«
...
6
7
8
9
10
...
»

Содержание SP97-XV



























































































Отзывы:

Нет отзывов

Похожие инструкции для SP97-XV

Бренд: Balluff Страницы: 62

Бренд: V2 ELETTRONICA Страницы: 12

Бренд: ECS Страницы: 52

Бренд: Zotac Страницы: 54

Бренд: IEI Technology Страницы: 8

Бренд: Aaeon Страницы: 44

Бренд: MSI Страницы: 22

Бренд: IBASE Technology Страницы: 91

Бренд: Acorp Страницы: 74

ISL70321SEHDEMO1Z

Бренд: Intersil Страницы: 9

Бренд: Bartels Mikrotechnik Страницы: 9

Бренд: DFI Страницы: 92

DisplayPort VIP Input Board

Бренд: Lattice Страницы: 21

Бренд: Avalue Technology Страницы: 29

Бренд: Gigabyte Страницы: 96

Бренд: EPOX Страницы: 64

E-TEC 40RL 2008

Бренд: Evinrude Страницы: 58

Бренд: Texas Instruments Страницы: 24

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды