Asus SP97-XV Скачать руководство пользователя страница 80

Страница: 80 / 90

ASUS SP97-XV User’s Manual

IX. SOFTWARE DRIVERS

(Autodesk ADI

4.2)

IX. Software Drivers

5. Autodesk ADI 4.2 -Protected Mode

5.0 General Description

5.0.1 Driver Files

1. The enclosed SiS 5597/5598 ADI driver contains the following file:

RCPSIS.EXP SiS ADI Driver (for all resolutions & colors)

Note: This version of ADI driver does not support 16-color operation.

2. This driver fits for a series of Autodesk Inc. products including:

(1) AutoCAD/386 R11

(2) AutoCAD/386 R12

(3) AutoShade/386 V2.0

(4) 3D Studio V3.0

3. Their installation procedures are different from one program to the others. But

the first step of installation is the same for all these programs, that is “To
unpack and copy drivers to where you would like them to reside.” Therefore,
we will state this step below.

4. As to the real installation procedures for each program, we will give a detail

description in Sec. 5.1 to Sec. 5.4.

5.0.2

Unpack & Copy

To unpack and copy drivers to where they should reside, please follow the following
procedures:

1. Run “INSTDRV.EXE” where it resides.

2. In “SiS Super VGA Drivers Installation” menu, select “A. ADI 4.2” to unpack

and copy drivers. (To select, type “A”)

3. In “Unpack & Copy ADI 4.2 Drivers” screen, keyin the “drive:\directory”

where these drivers would reside (default C:\ADI42). Program would
unpack & copy all related driver files to where you assign.

4. After “unpack and copy” completed, exit the INSTDRV.EXE program.

5. Refer to Sec. 5.1 to Sec. 5.4 for the real installation procedures for each

program.

Содержание SP97-XV



























































































Результаты поиска

Содержание SP97-XV

Отзывы:

Похожие инструкции для SP97-XV

Бренды по названию

Популярные бренды

Asus SP97-XV, Руководство пользователя

Результаты поиска

Содержание SP97-XV

Отзывы:

Похожие инструкции для SP97-XV

Бренды по названию

Популярные бренды