Asus SP97-XV Скачать руководство пользователя страница 87

Страница: 87 / 90

ASUS SP97-XV User’s Manual

IX. SOFTWARE DRIVERS

(OS/2 V3.0 (W

arp)

IX. Software Drivers

7. OS/2 V3.0 (Warp)

7.0 Driver & OS/2 Version Notes

1. The following description apply to “SiS 5597/5598 Driver Release V1.03” and

maybe later release version but not guaranteed.

2. All the OS/2 Warp Versions up to SiS 5597/5598 driver Rev. 1.03 would be

installed as described in this section except for Double Bytes OS/2 Warp (i.e.
Chinese, Japanese, Korea, etc.).

3. For Double Bytes OS/2 Warp installation, please refer to “Sec. 8 Double Bytes

OS/2 Warp”.

7.1 Driver Files

The enclosed SiS 5597/5598 OS/2 3.0 driver contains the following files:

SISINST.CMD

SiS driver install program

SVGA.EXE

SiS PMI Generator

S768256.DL@

SiS IBMDEV32.DLL Display Driver

OTHERS

other files required during installation

7.2 Installation

Before install SiS 5597/5598 OS/2 drivers, make sure:

1. Install your OS/2 system using “VGA display” option (i.e. standard VGA).

2. Start your OS/2 system.

Install SiS 5597/5598 OS/2 Warp drivers as following procedures:

1. Enter “OS/2 window” or “OS/2 full screen”.

2. Change directory to which holds the SiS 5597/5598 OS/2 3.0 display drivers

and type SISINST <Enter>. For example, A:\OS2\SBCS.30>SISINST

3. All the Driver Files will be copied to a subdirectory C:\SISDRV and the

“Select Screen parameters for SiS SVGA” menu appears and all the resolution
(and color) and frame rate supported would be shown on the screen.

4. Choose which one you would like to use and click “OK”.

5. Then installation program would complete all installation process and

create a “SiS Setup” for future change mode usage.

6. Shutdown and re-boot OS/2 to make your selection effectively.

Содержание SP97-XV



























































































Результаты поиска

Содержание SP97-XV

Отзывы:

Похожие инструкции для SP97-XV

Бренды по названию

Популярные бренды

Asus SP97-XV, Руководство пользователя

Результаты поиска

Содержание SP97-XV

Отзывы:

Похожие инструкции для SP97-XV

Бренды по названию

Популярные бренды