Asus SP97-XV Скачать руководство пользователя страница 38 | Manualshive

Страница: 38 / 90

background image

ASUS SP97-XV User’s Manual

38

IV. BIOS SOFTWARE

IV

. BIOS

(Standard CMOS)

The MODE entry is for IDE hard disks only, and can be ignored for MFM and ESDI
drives. This entry provides three options: Normal, Large, LBA, or Auto (see below).
Set MODE to the Normal for IDE hard disk drives smaller than 528MB; set it to
LBA for drives over 528MB that support Logical Block Addressing (LBA) to allow
larger IDE hard disks; set it to Large for drives over 528MB that do not support
LBA. Large type of drive can only be used with MS-DOS and is very uncommon.
Most IDE drives over 528MB support the LBA mode.

Autodetection of Hard Disks on Bootup
For each field, Primary Master, Primary Slave, Secondary Master, and Secondary
Slave, you can select Auto under the TYPE and MODE fields. This will enable auto
detection of your IDE disk drives during bootup. This will allow you to change your
hard disks (with the power off) and then power on without having to reconfigure
your hard disk type. If you use older hard disks that do not support this feature, then
you must configure the hard disk in the standard method as described earlier using
the “User” option.

NOTE: After the IDE hard disk drive information has been entered into BIOS, new
IDE hard disk drives must be partitioned (such as with FDISK) and then formatted
before data can be read from and write on. Primary IDE hard disk drives must have
its partition set to active (also possible with FDISK).

NOTE: SETUP Defaults are noted in parenthesis next to each function heading.

Drive A / Drive B (None)
These fields record the types of floppy disk drives installed in your system. The
available options for drives A and B are 360KB, 5.25 in.; 1.2MB, 5.25 in.; 720KB,
3.5 in.; 1.44MB, 3.5 in.; 2.88MB, 3.5 in.; None.

To enter the configuration value for a particular drive, highlight its corresponding
field and then select the drive type using the left or right arrow keys.

Floppy 3 Mode Support (Disabled)
This is the Japanese standard floppy drive. The standard stores 1.2MB in a 3.5-inch
disk drive. This is normally disabled but you may choose from either Drive A, Drive
B, Both, or Disabled.

Video (EGA/VGA)
Set this field to the type of video display card installed in your system. The options
are EGA/VGA, CGA 40, CGA 80, and Mono (for Hercules or MDA). If you are using
a VGA or any higher resolution card, choose EGA/VGA.

Halt On (All Errors)
This field determines which types of errors will cause the system to halt. Choose from
either All Errors; No Errors; All, But Keyboard; All, But Diskette; or All, But Disk/Key.

«
...
36
37
38
39
40
...
»

Содержание SP97-XV



























































































Отзывы:

Нет отзывов

Похожие инструкции для SP97-XV

Бренд: Yamaha Страницы: 96

TLV320AIC3111 EVM

Бренд: Texas Instruments Страницы: 39

Бренд: AOpen Страницы: 96

Бренд: Intel Страницы: 78

Бренд: Navia Страницы: 26

Бренд: ST Страницы: 11

Бренд: ZiLOG Страницы: 41

Бренд: R&S Страницы: 44

GA-AX370M-Gaming 3

Бренд: Gigabyte Страницы: 40

Бренд: Commell Страницы: 61

Бренд: Intel Страницы: 43

Бренд: Shuttle Страницы: 80

Z370 AORUS Gaming 7

Бренд: Gigabyte Страницы: 48

880GM-LE - V1.0

Бренд: ASROCK Страницы: 60

Бренд: JETWAY Страницы: 56

DisplayPort VIP Input Board

Бренд: Lattice Страницы: 21

Бренд: ECS Страницы: 60

Бренд: JETWAY Страницы: 53

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды