Associated Equipment 12-2415 Скачать руководство пользователя страница 11 | Manualshive

Страница: 11 / 37

background image

(BESA-12V24G) User Manual

Version GS 17628

11

Version GS 17628

EFB

tests Start/Stop or Enhanced Flooded Batteries.

GEL

tests Gel Cell VRLA Batteries with units of measurement in Cold Cranking Amps.

7. Before selecting the ratings ‘CCA, SAE, EN, IEC, DIN, CA and JIS #’ from the menu, check the battery

specification value. This value can be checked on the battery labels as some of the examples shown
below:

8.

Once the selection has been done, it will proceed to the display as shown below (Fig.24):

9. If the rating is selected under JIS # (Japanese Industrial Standard) then you need to refer to the

conversion chart provided separately with the Tester when purchased to convert to CCA ratings.

Refer to the battery model (example: 80D26L or NX110-5L) on the Cold Cranking Amps (CCA), WET is
580 CCA and AGM is 630 CCA.

10.

You can also use the rough CCA guide below, basing on the engine capacity of vehicle but the

percentage (%) Life is not that precise as compare to the actual battery rating due to this rough estimation.

1000 – 1299 cc

300 CCA

1300 – 1599 cc

400 CCA

1600 – 1999 cc

500 CCA

2000 – 2999 cc

700 CCA

3000 – 3500 cc

800 CCA

Fig.24

«
...
9
10
11
12
13
...
»

Содержание 12-2415






































Отзывы:

Нет отзывов

Похожие инструкции для 12-2415

Бренд: Landoll Страницы: 34

Бренд: Eagle Страницы: 3

Бренд: FENDT Страницы: 31

Бренд: SALUDA MEDICAL Страницы: 61

Бренд: Raymarine Страницы: 90

Бренд: DAKO Страницы: 25

Бренд: 3M ESPE Страницы: 50

Бренд: VACGEN Страницы: 13

Бренд: idiag Страницы: 10

Бренд: Bandit Страницы: 136

Versaflo S Series

Бренд: 3M Страницы: 11

DBI Sala EXOFIT

Бренд: 3M Страницы: 32

Бренд: 3M Страницы: 8

Бренд: Accurate Bio-Medical Technology Страницы: 35

Бренд: Raven Страницы: 12

Бренд: Zero 88 Страницы: 20

Бренд: Kapriol Страницы: 32

Бренд: Cabletron Systems Страницы: 33

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды