Assa Abloy Norton D6001BP-38-LH Скачать руководство пользователя

Страница: 20 / 28

in part without the express written permission of ASSA ABLOY Accessories and Door Controls Group, Inc. is prohibited.

80-9360-1030-020 Rev 6 11/20

D6021/D6031 Double Unit Series

(Push Side) Power Operator

Double Door Electric Dogging Exit Device Wiring

Double Door Hard Wired Executive Function Wiring

Factory Pre-Wiring Not Required to Change

•

For Master/Follow or Master-

Coord/Follow only (Sync

Cable must be used to

connect inverters.)

• Doors are normally closed.

• Activating switch will open

door.

•

Door will remain in indefinite

hold open until activating

switch is activated a second

time causing door to close.

Change Factory Pre-Wiring to Illustration Below (move NO to +24)

•

For Master/Follow or Master-

Coord/Follow only (Sync Cable

must be used to connect

inverters.)

• Doors are normally closed and

latched.

• Turning key switch ON will

apply power to exit device.

• First depression on device

touchpad will electrically dog

device for push/pull operation.

• Door will now open

automatically when wall switch

is depressed.

• Device will re-latch during

a power failure or when key

switch is turned off.

• Exit device allows egress at all

times. Exit device allows egress

during power failures.

• Current draw at Power Outputs

not to exceed 1.3 amps.

Содержание Norton D6001BP-38-LH





























Результаты поиска

Содержание Norton D6001BP-38-LH

Отзывы:

Похожие инструкции для Norton D6001BP-38-LH

Бренды по названию

Популярные бренды

Assa Abloy Norton D6001BP-38-LH, Руководство по установке

Результаты поиска

Содержание Norton D6001BP-38-LH

Отзывы:

Похожие инструкции для Norton D6001BP-38-LH

Бренды по названию

Популярные бренды