Assa Abloy Adams Rite EX89 Скачать руководство пользователя | Manualshive

Страница: 7 / 10

background image

Page | 7

P

800.872.3267

F

800.232.7329

E

[email protected]

www.adamsrite.com

Installing the Exit Device

NOTE: Use provided self-tapping screws for aluminum or hollow metal applications.

Use provided wood screws for wood applications.

1. INSTALL Mounting Foot on hinge side of door

using two (2) #10-32 x 3/4” pan head screws.
Leave screws slightly loosened for final
adjustment.

2. SLIDE the exit device onto the mounting foot

3. INSTALL Pullman Mounting Base on latch side of

door using two (2) #10-32 x 3/4” pan head
screws. Leave screws slightly loosened for final
adjustment.

«
...
5
6
7
8
9
...
»

Содержание Adams Rite EX89











Отзывы:

Нет отзывов

Похожие инструкции для Adams Rite EX89

Бренд: Yale Страницы: 10

Бренд: Falcon Страницы: 3

Бренд: Nalnor Страницы: 8

Бренд: Daikin Страницы: 36

Бренд: Vector Welding Страницы: 17

Бренд: omisa Страницы: 44

POWER CUT 60HFIII

Бренд: Mweld Страницы: 24

Бренд: Dorma Страницы: 6

RIRS 400HE EKO 3.0

Бренд: Salda Страницы: 34

Бренд: Firepower Страницы: 52

Бренд: Solar 3C Страницы: 38

Бренд: Woodhaven Страницы: 2

Бренд: Pamex Страницы: 2

Бренд: Pamex Страницы: 3

Бренд: Taurean Страницы: 2

Бренд: BFT Страницы: 16

Бренд: Power Plus Страницы: 9

Бренд: Von Duprin Страницы: 12

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды