Assa Abloy Adams Rite EX89 Скачать руководство пользователя | Manualshive

Страница: 8 / 10

background image

Page | 8

P

800.872.3267

F

800.232.7329

E

[email protected]

www.adamsrite.com

Installing the Strike Plate

1. INSTALL the Strike Plates using two (2) #10-32

x 3/4” flat head screws.

2. VERIFY that exit device is fully operational.
3. ADJUST strike plate as necessary.

4. MARK, CENTER PUNCH, DRILL 5/32” diameter

pilot hole for center screw.

5. INSTALL the #10-32 x 3/4” flat head self-

tapping center screw to maintain optimum
adjustment.

10-32 x 3/4"
flat head self-
tapping
screws, 2 qty

10-32 x 3/4"
flat head self-
tapping screw,
1 qty

«
...
6
7
8
9
10
»

Содержание Adams Rite EX89











Отзывы:

Нет отзывов

Похожие инструкции для Adams Rite EX89

Бренд: Jasic Страницы: 20

Бренд: R-Tech Страницы: 19

Arc Welder 55 - 160A

Бренд: Silverline Страницы: 46

Бренд: OSTBERG Страницы: 69

Бренд: Würth Страницы: 292

Бренд: SWS Страницы: 12

Бренд: SWS Страницы: 26

Бренд: Parkside Страницы: 201

Бренд: ABH Страницы: 2

Бренд: Electrex Страницы: 36

Бренд: ATE Pro. USA Страницы: 18

Бренд: ATE Страницы: 9

Бренд: Lister Страницы: 20

Бренд: Bug-O Systems Страницы: 20

Бренд: pro.point Страницы: 32

Бренд: Vector Welding Страницы: 36

Бренд: Daikin Страницы: 476

Бренд: Sunkko Страницы: 8

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды