ASM Zip-Spray-n-Roll 233792 Скачать руководство пользователя | Manualshive

Страница: 13 / 48

background image

13

309420

Priming

– Preparing to Spray Oil–Based Materials After Spraying Water–Based Materials

1. Turn Spray/Prime valve to PRIME.

PRIME

2. Separate prime tube (smaller) from suction

tube (larger).

3. Place prime tube in waste pail.

4. Submerge suction tube in mineral spirits.

prime
tube

suction

tube

WASTE

Mineral Spirits

5. Plug sprayer into grounded outlet.

6. Point Gun into waste pail.

WASTE

NOTE:

To spray water–based materials after spraying oil–based materials, follow the procedure outlined below,

using water instead of mineral spirits to flush system.

«
...
11
12
13
14
15
...
»

Содержание Zip-Spray-n-Roll 233792

















































Отзывы:

Нет отзывов

Похожие инструкции для Zip-Spray-n-Roll 233792

PFSP 100 - MANUEL 4

Бренд: Parkside Страницы: 64

Бренд: Parkside Страницы: 24

Бренд: Parkside Страницы: 53

Бренд: Ryobi Страницы: 4

Бренд: Ozito Страницы: 2

Бренд: Solo Страницы: 13

Бренд: jobmate Страницы: 9

Бренд: Performance Tool Страницы: 6

Бренд: Fimco Страницы: 14

Бренд: Fimco Страницы: 12

Бренд: Fimco Страницы: 12

Бренд: Fimco Страницы: 14

Бренд: Fimco Страницы: 6

Бренд: Hills Страницы: 12

Бренд: Kärcher Страницы: 300

Бренд: Workzone Страницы: 28

OptiSelect GM03

Бренд: Gema Страницы: 50

30.2000.00 VEGA

Бренд: PA Страницы: 4

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды