ASM Zip-Spray-n-Roll 233792 Скачать руководство пользователя | Manualshive

Страница: 35 / 48

background image

35

309420

Advanced Troubleshooting

General Problem: Motor Does Not Operate (continued)

SPECIFIC PROBLEM

CAUSE

SOLUTION

Basic Electrical Problems
(Continued)

Motor armature is shorting.

Check for shorts using armature tester (growler), or perform
spin test (see

Motor Diagnostics

on page 41). If shorts are

evident, replace motor using

Motor Kit

245080.

Control board is damaged.

CAUTION:

Do not perform control

board diagnostics until you have
determined that the armature is good.
A bad motor armature can burn out a
good control board.

See

Control Board Diagnostics

on page 41, and replace

control board if damaged using

Control Board Kit

245079.

Sprayer Wiring Problems

NOTE:

Remove right

enclosure mounting
screws, and pull right
enclosure away from drive
housing.

Take care to not

pull on the leads from
the electrical cord and
the Power switch (B).

Sprayer electrical cord is damaged.

Unplug sprayer electrical cord. Disconnect black electrical
cord wire at Power switch (B), and unplug in-line connection
of white electrical cord wire. Plug in electrical cord, and test
voltage between black and white electrical cord wires.
Meter must read 85 to130V AC.

Replace electrical cord if no voltage.

Sprayer power switch (B) is damaged.

Unplug sprayer electrical cord. Disconnect black control
board wire at Power switch (B), and unplug in-line
connection of white electrical cord wire. Plug in electrical
cord, turn Power switch ON, and test voltage between open
terminal of Power switch and white electrical cord wire.
Meter must read 85 to130V AC.

Replace Power switch (B) if no voltage.

Thermal overload cutoff switch is
damaged.

See

Startup Hazard After Thermal

Overload

in the WARNINGS section

on page 3.

Unplug sprayer electrical cord. Remove motor harness from
control card, and check for continuity between yellow leads
of motor harness. If thermal relief switch is open (no
continuity), allow motor to cool. If switch remains open after
motor cools, replace motor using

Motor Kit

245080.

If thermal relief switch closes after motor cools, find and
correct cause of overheating.

Terminals are damaged or loose.

Replace any damaged terminals, and make sure all
terminal connections are tight.

«
...
33
34
35
36
37
...
»

Содержание Zip-Spray-n-Roll 233792

















































Отзывы:

Нет отзывов

Похожие инструкции для Zip-Spray-n-Roll 233792

Бренд: WAGNER Страницы: 82

Бренд: WAGNER Страницы: 56

Бренд: WAGNER Страницы: 60

Бренд: WAGNER Страницы: 12

PEA-C4-HiCoat FM

Бренд: WAGNER Страницы: 28

Бренд: WAGNER Страницы: 112

Бренд: WAGNER Страницы: 47

Master III Series

Бренд: GAMA Страницы: 25

Бренд: WAGNER Страницы: 124

SPOT CHIEF SSC025212V

Бренд: Enduraplas Страницы: 24

NewRider 1700 HPA

Бренд: Newstripe Страницы: 26

Бренд: Siegen tools Страницы: 3

BLUEPLANET GERMSAFE24

Бренд: Wessol Страницы: 26

Бренд: HammerSmith Страницы: 64

Бренд: Rockwell Страницы: 12

Tree/TurfPro 61900

Бренд: Chapin Страницы: 36

Бренд: q-Tech Страницы: 15

Бренд: AFCO Страницы: 4

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды