ASM Zip-Spray-n-Roll 233792 Скачать руководство пользователя

Страница: 5 / 48

309420

The sprayer requires

a 120V AC, 60 Hz, 15A circuit

with grounding receptacle. Never use an outlet that is
not grounded or an adapter.

Do not use the sprayer if the electrical cord has a damaged
ground prong. Only use an extension cord with an undamaged,
3–prong plug.

Recommended extension cords

for use with this sprayer:

25 ft (7.6 m) 18 AWG

50 ft (15.2 m) 16 AWG

100 ft (30.5 m) 14 AWG

150 ft. (45.7 m) 12 AWG

Smaller gauge or longer extension cords may reduce sprayer
performance.

Grounding and Electric Requirements

ti5572a

Ground sprayer gun

through connection to a

properly grounded fluid hose and pump.

Ground fluid supply container.

Follow local code.

The sprayer must be grounded. Grounding reduces the risk of static and
electric shock by providing an escape wire for the electrical current due to
static build up or in the event of a short circuit.

ti3001b

Содержание Zip-Spray-n-Roll 233792

















































Результаты поиска

Содержание Zip-Spray-n-Roll 233792

Отзывы:

Похожие инструкции для Zip-Spray-n-Roll 233792

Бренды по названию

Популярные бренды

ASM Zip-Spray-n-Roll 233792, Операция, ремонт и запасные части.

Результаты поиска

Содержание Zip-Spray-n-Roll 233792

Отзывы:

Похожие инструкции для Zip-Spray-n-Roll 233792

Бренды по названию

Популярные бренды