manualshive.com logo in svg

ASG OM Series, Руководство пользователя

Поделиться
Скачать
ASG OM Series Скачать руководство пользователя страница 7

ASG, Division of Jergens, Inc.  

15700

 S. Waterloo Road | Cleveland, OH 44110-3898 | Phone: (888) 486-6163 | Fax: (216) 481-4519 | Email: [email protected] | Web: www.asg-jergens.com

7

Adjustments and Checks before Use

Check the Model Number

Ensure the model number of the screw presenter is appropriate for the size of screw 
you are using. 
Before delivery, each section of the machine is checked and adjusted with panhead 
screws matching the nominal diameter of the model ordered. Operate the machine 
with the screws loaded to check that the pick up is smooth. If the height or shape of 
the screw head is different each section must be readjusted. If this is the case, make 
the following checks and adjustments:
•  Check the screw load amount
•  Check and adjust the passing plate
•  Check and adjust the holding plate 
•  Check and adjust the timer
•  Check and adjust the brush
•  Check and adjust the rail vibration
•  Check and adjust the front and rear sides of the rail
If the rail, escape, robot escape guide and passing plate are replaced, screws with 
a different nominal diameter can be accepted. After these parts are replaced, fine 
adjusting is required.

Содержание OM Series


































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды