background image

CZ

8

Pool Water Connection

The pool water to be measured must be connected to PP60 pH. 
Connect the measured water inlet downstream of the pump, upstream of the 
fi lter and ZPM (coagulation mixer).

Place the water valve fi tting to the T-joint, blinded by DN50 G1/4” threaded 
plug #12134.

• 

The connecting fi tting is installed in G1/4” thread. 

Aseko provides the unique Speedfi t connecting fi tting for measured water 
connection to your PP60 pH. To connect the interconnecting tube, push it 
into the Speedfi t connector and then lock it by pulling back. To disconnect 
the interconnecting tube, push and hold a circular collet and pull the 
interconnecting tube out. 

WARNING:

 To treat PE tube ends, use a sharp knife (part of delivery). The 

use of scissors or tongs deforms the tube end and leads to leaks.

WARNING:

 Only hand tighten. Do not use tongs or any other tools.

1. 

To ensure tightness of joints, cut the tube at 90 ° angle.

• 

Use the sharp knife to cut plastic. The cut must be clean and smooth.

2. 

Connect the water inlet to the measured water fi lter connection and the 
water outlet to the probe housing connection. Make sure that measured 
water pressure does not exceed 1.5 bar.

3. 

The water outlet  can be realized:

1. downstream of fi ltration
2. to non-pressure (overfl ow tank)
3. upstream of fi lter pump

After the water inlet has been connected and opened, your PP60 pH is ready 
to measure and adjust the pH and Cl value in your pool so as to achieve the 
required values.

Water valve 

fi tting

G1/4” thread

6.2x4 hose

CONNECTION

LOCKING

DISCONNECTION

Water valve fi tting

Inserting DN50 

plug

G1/4” threaded

T-joint

6.2x4 hose

90°

Pull out

Содержание 13260

















Отзывы: