ASCOM UPAC - Скачать руководство пользователя страница 38

Страница: 38 / 103

TD 92483GB

2008-06-05/ Ver. B

Installation and Operation Manual
UPAC- Unite Packet for Messaging and Alarm

Click “Activate”.

Flow control:

Used for handshaking control. Default: None

ESPA dialect:

Select dialect, with or without an extra Carriage
Return (CR).
Default: TeleCourier extensions (i.e. Ascom dialect)

Control station selection:

Determines which module shall act as control
station. Default: External equipment.

Address of external equipment: Enter address (0 - 9). Default: 1

Address of this module:

Enter address (0 - 9). Default: 2

Default Call ID:

Number to call if not specified in the external
equipment. Default:000

Default display message:

Message to display if not specified in the external
equipment. Default:BLANK

Default message priority:

Priority if not specified in the external equipment.
Default: 7 (Normal)

Default beep code:

Beep code if not specified in the external
equipment.
Default: 2 beeps.

Default method for ack.:

Select how the paging shall be acknowledged if
not specified by the external equipment.
Default: No Ack.

Default urgency:

Urgency if not specified in the external equipment.
Default: Normal.

Transmission delay (x10 ms):

How long to wait before transmission to external
equipment. Default: 30 milliseconds

Identical pagings treatment:

How to handle identical pagings.
Default: Not accepted.

Running no. to external
equipment:

If running number shall be sent or not. Default: No

Timeout mode:

Determines when to start timeout mode i.e.
remove paging from queue. Default: after "Call
Terminated" call status.

Timeout mode TTL (seconds):

Determines the time for timeout mode i.e. during
this time the paging remains in the queue after the
"Timeout mode" has started. Default: 5 seconds.

Manual Ack type:

Dependent on if the external equipment supports
negative acknowledge. Default: Positive and
Negative manual acknowledge.

Manual Ack TTL (minutes):

How long a paging with manual acknowledge
remains in the queue after transmission of

Call

Terminated call status.

Default: 5 minutes.

Message Ref. ID TTL (minutes): How long a Message Reference ID remains in

queue. Only valid for Ascom dialect.
Default: 5 minutes.

ASCII conversion table:

Makes it possible to convert display message
characters.

Содержание UPAC -








































































































Результаты поиска

Содержание UPAC -

Отзывы:

Бренды по названию

Популярные бренды

ASCOM UPAC -, Инструкция по установке и эксплуатации

Результаты поиска

Содержание UPAC -

Отзывы:

Бренды по названию

Популярные бренды