ASCOM UPAC - Скачать руководство пользователя страница 12

Страница: 12 / 103

TD 92483GB

2008-06-05/ Ver. B

Installation and Operation Manual
UPAC- Unite Packet for Messaging and Alarm

2.5

Function LED Indications

The function indicator shows the UPAC status (LED1 on the circuit board). For the
placement of LED1, refer to the illustration in

figure 45

on page 26.

The table below shows which indication refers to which status.

2.6

Information required for the Setup

Make sure the following information is available:

• MAC address – found on the licence certificate enclosed in delivery

• Licence number – found on the licence certificate enclosed in delivery

• Network parameters – ask your network administrator

• Type of connected wireless phone system

• IP address to connected system (if connected via IP)

• Other messaging systems to send messages to (optional)

• IP address to mail server if fault information and Activity Logs are to be sent to e-mail

recipients (optional)

• LDAP properties if an LDAP server is used (optional)

Figure 8.

Fail safe mode is indicated, even if SW3 pin 2 is not set to ON, if the application on UPAC is not completely

installed or when the application part of the Compact Flash is erased.

When UPAC is in Network setup mode, this will always be indicated and override LED indications of other

simultaneously activated modes, for example Image installation mode.

Starting up mode is indicated during start of applications or if an application has lost connection to a

required resource, for example DECT Exchange.

Status

Colour

Green

Orange

OK. Running

Fail-safe mode

Network setup mode

LED Indication

Red

Orange

Red

Starting up

Orange

Image installation mode

Power up
Restart

Halted (auto. restart after 10 min.)

Unlicensed mode

Low voltage

Licence error

Watch-dog reset

Shut-down

Memory error (3 s ON / 3 s OFF)

Network error (IP interface initiation error)
Module key error (Module key not found)

Each segment = 100 ms

007

Содержание UPAC -








































































































Результаты поиска

Содержание UPAC -

Отзывы:

Бренды по названию

Популярные бренды

ASCOM UPAC -, Инструкция по установке и эксплуатации

Результаты поиска

Содержание UPAC -

Отзывы:

Бренды по названию

Популярные бренды