Asante IntraCore 39240 Скачать руководство пользователя страница 129

Страница: 129 / 148

10.4.110.8 spanning-tree mst

Configure a multiple spanning tree instance.

1) spanning-tree mst instance

This command creates or removes a MST instance

spanning-tree mst instance add

This command creates a MST instance.

Format

spanning-tree mst instance add vlan <

vlan list

> mstpid <

MST ID

Mode

Global Config

e.g. Switch(Config)# Spanning-Tree mst instance add vlan 2-5 mstpid 2
Switch(Config)# Spanning-Tree mst instance add vlan 6 mstpid 3

spanning-tree mst instance delete

This command removes the last MST instance.

Format

spanning-tree mst instance delete

Mode

Global Config

2 )spanning-tree mst vlan

This command adds or deletes vlan frome a MSTP instance.

spanning-tree mst vlan <MST ID> <vlan list> add

This command creates a MST instance.

Format

spanning-tree mst vlan <

MST ID

> <

vlan list

> add

Mode

Global Config

e.g. Switch(Config)# Spanning-Tree mst vlan 3 3-5 add

Spanning-Tree mst vlan <MST ID> <vlan list> delete

This command deletes a vlan from a MST instance.

Format

Spanning-Tree mst vlan <

MST ID

> < vlan

list

> delete

Mode

Global Config

3) spanning-tree mst bridgepri

This command configures bridge priority for a MST instance.

Format

spanning-tree mst bridgepri <

MST ID

> <

priority

Mode

Global Config

4) spanning-tree mst cost

This command configures port path cost in a MST instance.

Format

spanning-tree mst cost <

MST ID

> <

path cost

> ports <

port list

Mode

Global Config

5)spanning-tree mst priority

This command configures port priority in a MST instance

Format

spanning-tree mst priority <

MST ID

> <

priority

> ports <

port list

Mode

Global Config

10.4.20 User commands

This command changes user password.

Format

user password

Mode

Global Config

10.4.21 Interface commands

This command enters into configure interface mode.

Format

Interface <

port-ID

Mode

Global Config

10.4.22 rmon

This command is used to configure RMON.

10.4.22.1 rmon event

This command creates rmon event entry.

Format

rmon event index <

1..65535

> desc <

WORD

> event <

1..4

community <

WORD

>owner<

WORD

Mode

Global Config

e.g. Switch(Config)# rmon event index 1 desc 123 event 4 community 123
owner test

10.4.22.2 rmon alarm

129

Asante IntraCore IC39240/480

User’s Manual

Содержание IntraCore 39240





















































































































































Результаты поиска

Содержание IntraCore 39240

Отзывы:

Похожие инструкции для IntraCore 39240

Бренды по названию

Популярные бренды

Asante IntraCore 39240, Руководство пользователя

Результаты поиска

Содержание IntraCore 39240

Отзывы:

Похожие инструкции для IntraCore 39240

Бренды по названию

Популярные бренды