Asante IntraCore 39240 Скачать руководство пользователя страница 118

Страница: 118 / 148

This command is used to forward frame and learn SA into ARL table

Format

vlan ingress bypass

Mode

Global Config

10.4.2.4 vlan port

This command is used to configure 802.1Q port parameters for vlans

1) vlan port all

This command is used to configure all ports

vlan port all port-configure

This command is used to configure ports in a specific vlan

Format

vlan port all port configure <

vlan-ID

Mode

Global Config

vlan port all protected

This command is used to configure protected ports

Format

vlan port all protected {enable|disable}

Mode

Global Config

vlan port all pvid

This command is used to configure port pvid

Format

vlan port all pvid <

vlan-ID

Mode

Global Config

2) vlan port ports

This command is used to configure multiple ports

vlan port ports port-configure

This command is used to configure ports in a specific vlan

Format

vlan port ports port-configure <

vlan-ID

Mode

Global Config

vlan port ports protected

This command is used to configure protected ports

Format

vlan port ports protected {enable|disable}

Mode

Global Config

vlan port ports pvid

This command is used to configure port vid

Format

vlan port ports pvid <

vlan-ID

Mode

Global Config

10.4.2.5 vlan lag

This command is used to configure lag to a special vlan

1) vlan lag vlan < vlan-id> exclude

25
This command is used to remove lag from a vlan

Format

vlan lag vlan <

vlan-ID

> exclude lags <

lag-ID

Mode

Global Config

2) vlan lag vlan <vlan-ID> untagged

This command is used to set to untagged lag.

Format

vlan lag vlan <

vlan-ID

> untagged lags <

lag-ID

Mode

Global Config

3) vlan lag vlan <vlan-ID> tagged

This command is used to set to tagged lag.

Format

vlan lag vlan <

vlan-ID

> tagged lags <

lag-ID

Mode

Global Config

10.4.3 Bridge

This command is used to configure switch aging time

Format

bridge aging-time <0-1048575>

Mode

Global Config

10.4.4 lacp-syspri

This command is used to configure lacp system priority

Format

lacp-syspri system-priority <0-65535>

Mode

Global Config

118

Asante IntraCore IC39240/480

User’s Manual

Содержание IntraCore 39240





















































































































































Результаты поиска

Содержание IntraCore 39240

Отзывы:

Бренды по названию

Популярные бренды

Asante IntraCore 39240, Руководство пользователя

Результаты поиска

Содержание IntraCore 39240

Отзывы:

Бренды по названию

Популярные бренды