Asante IntraCore 39240 Скачать руководство пользователя страница 136

Страница: 136 / 148

and 0 means no limit.

Format

storm-control broadcast <

rate

Mode

Interface Config

10.5.14.3 storm-control broadcast-multicast

This command storm control limited
value :0,64,256,1024,10240,65536.102400,1024000,which the unit is Kbps
and 0 means no limit.

Format

storm-control broadcast-multicast <

rate

Mode

Interface Config

10.5.14.4 storm-control broadcast-unknown

This command storm control limited
value :0,64,256,1024,10240,65536.102400,1024000,which the unit is Kbps
and 0 means no limit.

Format

storm-control broadcast-unknown <

rate

Mode

Interface Config

e.g. Switch(Interface 1)# storm-control broadcast-unknown 64

10.5.14.5 storm-control all-cast

This command storm control limited
value :0,64,256,1024,10240,65536.102400,1024000,which the unit is Kbps
and 0 means no limit.

Format

storm-control all-cast <

rate

Mode

Interface Config

10.5.15 rmon-counter command

This command specifies rmon counter capability on a port

Format

rmon-counter {enable|disable}

Mode

Interface Config

10.5.16 set igmp-router-port command

This command specifies igmp router port .

Format

set igmp-router-port {ebable|disable}

Mode

Interface Config

10.5.17 spanning-tree command
10.5.17.1 spanning-tree cost

This command configure RSTP port path cost, path cost value:0~200000000.

Format

spanning-tree cost <

pathcost

Mode

Interface Config

10.5.17.2 spanning-tree edge

This command configure edge property

Format

spanning-tree edge {enable|disable}

Mode

Interface Config

e.g. Switch(Interface 1)# spanning-tree edge enable
47

10.5.17.3 spanning-tree force-p2plink

This command configure force point to point link mode.

Format

spanning-tree force-p2plink {auto|enable|disable}

Mode

Interface Config

10.5.17.4 spanning-tree migration-check

This command re-checks the appropriate BPDU format to send on this port

Format

spanning-tree migration-check {enable|disable}

Mode

Interface Config

10.5.17.5 spanning-tree mst

This command configures multiple spanning tree instance.

1) spanning-tree mst cost

This command configure the path cost on a MST instance :1~200000000.

Format

spanning-tree mst cost <

pathcost

Mode

Interface Config

2) spanning-tree mst priority

136

Asante IntraCore IC39240/480

User’s Manual

Содержание IntraCore 39240





















































































































































Результаты поиска

Содержание IntraCore 39240

Отзывы:

Похожие инструкции для IntraCore 39240

Бренды по названию

Популярные бренды

Asante IntraCore 39240, Руководство пользователя

Результаты поиска

Содержание IntraCore 39240

Отзывы:

Похожие инструкции для IntraCore 39240

Бренды по названию

Популярные бренды