Art's Way 1222AHS Скачать руководство пользователя страница 20 | Manualshive

Страница: 20 / 30

background image

18

1222AHS OPERATORS MANUAL – LIGHT KIT ASSEMBLY

L

AMP

I

NSTALLATION

1.

Connect wires from warning lamps (#2) to
terminals of wiring harness (#4).

2.

Connect tail lamps (#1) to terminals of wiring
harness (#4).

3.

Connect primary harness (#3) to towing vehicle
with 7-pin connector. Plug primary harness (#3) to
converter module (#9).

4.

Install converter module (#9) to defoliator frame
using hardware provided. Plug the tail light
harness (#4) into the converter module.

5.

Check tail light operation. The amber lamps will
flash in unison with the towing vehicle warning
lights. The red tail lamps will light continuous when
road lamps of towing vehicle are engaged. When
signaling a left or right turn, the amber light
opposite the turn will light continuous and the
amber light in the direction of the turn will flash at
an increased rate. The red light on the turn side
will also flash with the amber light signaling the
turn.

«
...
18
19
20
21
22
...
»

Содержание 1222AHS































Отзывы:

Нет отзывов

Похожие инструкции для 1222AHS

Бренд: ABB Страницы: 27

Бренд: Pall Страницы: 51

Бренд: ZAMST Страницы: 21

Бренд: MacDon Страницы: 89

Бренд: Yates Страницы: 2

Бренд: JAC Страницы: 100

Бренд: ADVANCED HOME CARE Страницы: 16

Бренд: ZIGBEE Страницы: 4

Бренд: CAIRE Страницы: 38

Бренд: Caframo Страницы: 72

Бренд: YYZ Lighting Страницы: 3

Бренд: Camp Safety Страницы: 118

Бренд: Ultrafast Systems Страницы: 39

Бренд: Mackworth Страницы: 2

Бренд: IEMCA Страницы: 82

KID 80-IV Touch

Бренд: IEMCA Страницы: 122

Бренд: Calrec Страницы: 92

Бренд: Ransomes Страницы: 282

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды