artisan Agilent Скачать руководство пользователя страница 24

Страница: 24 / 70

Installation

Assembling the XY Autosampler

Figure 8

Needle Guide of Sampler Needle

Installing Needle Holder

To install the needle holder, slide it into place on the needle holder bracket
and secure with the supplied screw.

Installing Needle

To install the needle:

Slide the needle into the tubing fitting.

Connect the transfer tubing from the dilutor, if installed, to the tubing fitting.

Slide the needle assembly into the needle holder on the vertical arm making
sure that the needle is centered over the needle guide.

Secure the needle by tightening the needle retaining screw.

Rinse Station and Support Bar Installation

N O T E

The terms

rinse station

and

wash station

are used synonymously through

out this manual.

The support bar attaches to the front face of the XY autosampler. Its rear
contains mounting holes for rinse

stations and its top contains mounting

holes for transfer ports and filler ports.

Rinsing Well

From left to right, the ports in a rinse station are the rinsing well,
level-sensing rinsing well, and drain. See Figure 9 for more details.

Before mounting the rinse station, you should make a decision as to whether
you want to use a

•

non

-flow-through rinse station — rinsing well,

or a

needle guide

lock washer

Artisan Technology Group - Quality Instrumentation ... Guaranteed | (888) 88-SOURCE | www.artisantg.com

Содержание Agilent







































































Результаты поиска

Содержание Agilent

Отзывы:

Бренды по названию

Популярные бренды

artisan Agilent, Руководство оператора

Результаты поиска

Содержание Agilent

Отзывы:

Бренды по названию

Популярные бренды