Arthrex AR-6480 Скачать руководство пользователя страница 14 | Manualshive

Страница: 14 / 49

background image

Product Description

DualWave Arthroscopy Pump

User’s Guide

LM1-0630-EN_E

Page 8 of 43

AR-6480 Display Messages

2.2.3

The console’s Touch Panel Visual Display (TPVD) [5] provides information about
the status of the AR-6480 and the pressure and flow settings in real time. Table 3
describes each message and button when pump is in ready state.

Table 3

Touch Panel Visual Display Messages AND Iconography

Message

Cause

Explanation

Arthrex DualWave

Message appears when the AC mains power
switch is activated.

Power on message display.

** Tubing Out **

Message appears when tubing is not plugged
into the Tubing Sensor Coupler [2].

Check tubing installation.

** Door Open **

Message appears when the roller housing door
[12] or [9] is open.

Roller housing door is not
closed.

** Over Pressure **

Message appears when the sensed pressure
exceeds over-pressure software limit of 300
mmHg.

Software overpressure
condition.

Critical Failure

Message appears on the first line of the TPVD if
one of three conditions is met:

Failure Condition 1: ** Power Failure **

Appears if the power supply self-test fails when
the pump is turned on.

Failure Condition 2: ** OVP Detect Fail

*

*

Appears if the hardware overpressure diagnostic
test fails when the pump is turned on.

Failure Condition 3: ** Sensor Failure **

Appears if the pump detects a problem with the
pressure sensors.

Critical failure, cannot
continue operation.

** Power Failure **

Message appears if the power supply self-test
fails when the pump is turned on.

Power supply test fails.

** OVP Detect Fail **

Message appears if the hardware overpressure
diagnostic test fails when the pump is turned on.

Hardware overpressure
diagnostic fails.

** Sensor Failure **

Message appears if the pump detects a problem
with the pressure sensors.

Sensor failure.

** Pressure Fault **

Message appears when the pump is unable to
reach a desired set pressure within a specific
amount of time. This typically indicates an
improperly installed tubing set or a split in the
tube from continuous use.

Insufficient measured
pressure.

Remote Control Icon

Icon appears when the remote is attached.

Remote connected.

Foot Pedal Icon

Icon appears when the foot pedal is attached.

Foot pedal connected,

+

Button

The TPVD displays the pressure reading until
PRESSURE (+) button is pressed. Once pressed,
the displayed pressure reading will change to
the pressure setting. Each subsequent press of
the pressure buttons will increase the pressure
setting in increments of 5.

Pressure set increase,

«
...
12
13
14
15
16
...
»

Содержание AR-6480


















































Отзывы:

Нет отзывов

Похожие инструкции для AR-6480

Бренд: Landoll Страницы: 6

Бренд: ParaBody Страницы: 9

Бренд: ParaBody Страницы: 3

Бренд: MacDon Страницы: 45

Бренд: H&S Страницы: 30

Бренд: ZOLL Страницы: 5

Бренд: Accu-Chek Страницы: 3

Бренд: iBin Страницы: 2

Бренд: UNIA Страницы: 62

Бренд: Jackco Страницы: 6

Бренд: Hakko Electronics Страницы: 8

Professional HS 8

Бренд: Hailo Страницы: 5

Бренд: Hainbuch Страницы: 52

Бренд: Ibiza Страницы: 21

Бренд: IBC Страницы: 8

Бренд: Ibanez Страницы: 8

Бренд: IAI Страницы: 5

Бренд: Ideal Heating Страницы: 16

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды