ARM Cortex-R4 Скачать руководство пользователя страница 368

Страница: 368 / 436

Signal Descriptions

ARM DDI 0363G

A-10

ID073015

Non-Confidential

A.5.2

AXI master port error detection signals

Table A-5

shows the AXI master port error detection signals. these signals are only generated

if the processor is configured to include AXI bus parity. See

Configurable options

on page 1-6

for more information.

ARREADYM

Input

CLKIN

Address ready. The slave uses this signal to indicate that it can
accept the address.

ARSIZEM[2:0]

Output

CLKIN

Indicates the size of the transfer.

ARUSERM[4:0]

Output

CLKIN

Provides decode information for the read address channel. See

Table 9-3 on page 9-5

for information about the encoding of this

signal.

ARVALIDM

Output

CLKIN

Indicates address and control are valid.

Read Data Channel

RDATAM[63:0]

Input

CLKIN

Read data.

RIDM[3:0]

Input

CLKIN

The identification tag for the read data group of signals.

RLASTM

Input

CLKIN

Indicates the last transfer in a read burst.

RREADYM

Output

CLKIN

Read ready signal indicating that the bus master can accept read
data and response information.

RRESPM[1:0]

Input

CLKIN

Read response.

RVALIDM

Input

CLKIN

Indicates that read data is available.

Table A-4 AXI master port signals for the L2 interface (continued)

Signal

Direction

Clocking

Description

Table A-5 AXI master port error detection signals

Signal

Direction

Clocking

Description

AWPARITYM

Output

CLKIN

Parity bit for write address channel

WPARITYM

Output

CLKIN

Parity bit for write data channel

BPARITYM

Input

CLKIN

Parity bit for write response channel

ARPARITYM

Output

CLKIN

Parity bit for read address channel

RPARITYM

Input

CLKIN

Parity bit for read data channel

AXIMPARERR[1:0]

Output

CLKIN

Parity error indication for read data, bit [1], and write response,
bit[0], channels

Содержание Cortex-R4


















































































































































































































































































































































































































































Результаты поиска

Содержание Cortex-R4

Отзывы:

Похожие инструкции для Cortex-R4

Бренды по названию

Популярные бренды

ARM Cortex-R4, Техническое справочное руководство

Результаты поиска

Содержание Cortex-R4

Отзывы:

Похожие инструкции для Cortex-R4

Бренды по названию

Популярные бренды