manualshive.com logo in svg

ARM Cortex-R4, Техническое справочное руководство

Продукт ARM Cortex-R4 - это высокопроизводительный микропроцессор, разработанный для реального времени. Вы можете скачать бесплатно Технический справочник для данного продукта с {сайт} и ознакомиться с подробной информацией о его функциях и возможностях.

Поделиться
Скачать
background image

Debug 

ARM DDI 0363G

Copyright © 2006-2011 ARM Limited. All rights reserved.

12-17

ID073015

Non-Confidential

To use the Debug Status and Control Register, read or write CP14 c1 with:

[8]

Sticky Undefined

Sticky Undefined bit:
0 = no Undefined Instruction exception occurred in debug state since the last time this bit 
was cleared
1 = an Undefined Instruction exception occurred while in debug state since the last time 
this bit was cleared.
This flag detects Undefined Instruction exceptions generated by instructions issued to the 
processor through the DBGITR. This bit is set to 1 when an Undefined Instruction 
exception occurs while the processor is in debug state and is cleared by writing a 1 to 
DBGDRCR[2].

[7]

Sticky 
asynchronous 
abort

Sticky asynchronous Data Abort bit:
0 = no asynchronous Data Aborts occurred since the last time this bit was cleared
1 = an asynchronous Data Abort occurred since the last time this bit was cleared.
This flag detects asynchronous Data Aborts triggered by instructions issued to the 
processor through the DBGITR. This bit is set to 1 when an asynchronous Data Abort 
occurs while the processor is in debug state and is cleared by writing a 1 to DBGDRCR[2].

[6]

Sticky 
synchronous 
abort

Sticky synchronous Data Abort bit:
0 = no synchronous Data Abort occurred since the last time this bit was cleared
1 = a synchronous Data Abort occurred since the last time this bit was cleared.
This flag detects synchronous Data Aborts generated by instructions issued to the 
processor through the DBGITR. This bit is set to 1 when a synchronous Data Abort occurs 
while the processor is in debug state and is cleared by writing to the DBGDRCR[2].

[5:2]

MOE

Method of entry bits:
b0000 = a 

DBGDRCR[0]

 halting debug event occurred

b0001 = a breakpoint occurred
b0100 = an 

EDBGRQ

 halting debug event occurred

b0011 = a BKPT instruction occurred
b1010 = a synchronous watchpoint occurred
others = reserved.
These bits are set to indicate any of:
•

the cause of a debug exception

•

the cause for entering debug state.

A Prefetch Abort or Data Abort handler must check the value of the CP15 Fault Status 
Register to determine whether a debug exception occurred and then use these bits to 
determine the specific debug event.

[1]

a

Core restarted

Core restarted bit:
0 = the processor is exiting debug state
1 = the processor has exited debug state. This is the reset value.
The debugger can poll this bit to determine when the processor responds to a request to 
leave debug state.

[0]

a

Core halted

Core halted bit:
0 = the processor is in normal state. This is the reset value.
1 = the processor is in debug state.
The debugger can poll this bit to determine when the processor has entered debug state.

a. These bits always reflect the status of the processor, therefore they only have a reset value if the particular reset event affects 

the processor. For example, a 

PRESETDBGn

 event leaves these bits unchanged and a processor reset event such as 

nSYSPORESET

 sets DBGDSCR[18] to a 0 and DBGDSCR[1:0] to 10.

Table 12-10 DBGDSCR Register bit assignments (continued)

Bits

Name

Function

Содержание Cortex-R4





















































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для Cortex-R4

Love Controls Loop Alarm Installation Instructions Manual preview
Loop Alarm
Бренд: Love Controls Страницы: 8
Cookworks FP9076-GS Care & Instruction Manual preview
FP9076-GS
Бренд: Cookworks Страницы: 13
dexbaby Make, Store & Serve Instruction Sheet preview
Make, Store & Serve
Бренд: dexbaby Страницы: 2
Coline 34-2403 Instruction Manual preview
34-2403
Бренд: Coline Страницы: 24
Mitsubishi Electric EY-3D-EMT2H User Manual preview
EY-3D-EMT2H
Бренд: Mitsubishi Electric Страницы: 8
Mitsubishi Electric 236CB Features preview
236CB
Бренд: Mitsubishi Electric Страницы: 2
Mitsubishi Electric OL-X500SZ Specifications preview
OL-X500SZ
Бренд: Mitsubishi Electric Страницы: 1
Grundig CUISINERY MM 8050 Product Data preview
CUISINERY MM 8050
Бренд: Grundig Страницы: 1
Grundig UM 8050 Manual preview
UM 8050
Бренд: Grundig Страницы: 16
Grundig CH 6280 L Instruction Manual preview
CH 6280 L
Бренд: Grundig Страницы: 11
Grundig CH 8680 Manual preview
CH 8680
Бренд: Grundig Страницы: 88
Artesyn PmPPC440 User Manual preview
PmPPC440
Бренд: Artesyn Страницы: 99
Audipack Quatro-Fix QFIX-0100G Installation Manual preview
Quatro-Fix QFIX-0100G
Бренд: Audipack Страницы: 2
Blackbox VWP-1060 User Manual preview
VWP-1060
Бренд: Blackbox Страницы: 40
Hamilton Beach 72860 Use & Care preview
72860
Бренд: Hamilton Beach Страницы: 2
Hamilton Beach 70550 - PrepStar Food Processor Use & Care Manual preview
70550 - PrepStar Food Processor
Бренд: Hamilton Beach Страницы: 32
Ruris ST100 Manual preview
ST100
Бренд: Ruris Страницы: 97
Altec Lansing 4024A SIGNAL PROCESSING Specifications preview
4024A SIGNAL PROCESSING
Бренд: Altec Lansing Страницы: 4

Бренды по названию

Популярные бренды

Загрузить еще бренды