ARM Cortex-R4 Скачать руководство пользователя страница 105

Страница: 105 / 436

System Control

ARM DDI 0363G

4-35

ID073015

Non-Confidential

The LineSize field is encoded as 2 less than log(2) of the number of words in the cache line. For
example, a value of

0x0

indicates there are four words in a cache line, that is the minimum size

for the cache. A value of

0x1

indicates there are eight words in a cache line.

Table 4-20

shows the individual bit field and complete register encodings for the CCSIDR. Use

this to match the cache size and level of cache set by the CSSELR. See

c0, Cache Size Selection

Register

on page 4-36

To access the CCSIDR read CP15 with:

MRC p15, 1, <Rd>, c0, c0, 0 ; Read CCSIDR

4.3.13

c0, Current Cache Level ID Register

The CLIDR Register characteristics are:

Purpose

•

Indicates the cache levels that are implemented. Architecturally,
there can be a different number of cache levels on the instruction and
data side.

•

Captures the point-of-coherency.

•

Captures the point-of-unification.

Usage constraints

The CLIDR is:
•

a read-only register

•

accessible in Privileged mode only.

Configurations

Available in all processor configurations.

Attributes

See

Table 4-21 on page 4-36

[27:13]

NumSets

Indicates the number of sets as
(number of sets) - 1

[12:3]

Associativity

Indicates the number of ways as
(number of ways) - 1

[2:0]

LineSize

Indicates the number of words in each cache line

a. See

Table 4-20

for valid bit field encodings.

Table 4-20 Bit field and register encodings for CCSIDR

Size

Complete
register
encoding

Register bit field encoding

NumSets

Associativity

LineSize

4KB

0xF003E019

0x001F

0x3

0x1

8KB

0xF007E019

0x003F

16KB

0xF00FE019

0x007F

32KB

0xF01FE019

0x00FF

64KB

0xF03FE019

0x01FF

Table 4-19 CCSIDR Register bit assignments (continued)

Bits Name

Function

Содержание Cortex-R4


















































































































































































































































































































































































































































Результаты поиска

Содержание Cortex-R4

Отзывы:

Похожие инструкции для Cortex-R4

Бренды по названию

Популярные бренды

ARM Cortex-R4, Техническое справочное руководство

Результаты поиска

Содержание Cortex-R4

Отзывы:

Похожие инструкции для Cortex-R4

Бренды по названию

Популярные бренды