background image

25

C1 = FAN
1:

“Hall” sensor power supply 12V (red)

2:

“Hall” sensor ground (blue)

3:

Not used

4:

Start of coil (black)

5:

“Hall” sensor input (white)

6:

End of coil (brown)

C2 = POWER SUPPLY
1:

Earth (yellow/green)

2:

Earth (yellow/green)

3:

Not connected

4:

Neutral (blue)

5:

Not connected

6:

Live (brown)

C3 = CONNECTION TO ROOMSTAT
1:

Input - 1

2:

Input - 2

C4 = TIMER 
1:

3 V output

2:

Timer ground

3:

Timer output

4:

Not connected

C5 = REMOTE CONTROL (Bus+/Bus-)
1:

Input/output-1

2:

Input/output-2

C6 = SENSOR CONNECTOR
1:

Domestic hot water flow switch (grey)

2:

Main circuit flow switch (grey)

3:

Under floor heating thermostat (grey)

4:

Heating flow sensor (grey)

5:

Heating return sensor (grey)

6:

Domestic hot water sensor (grey)

7:

Not used: jumper

8:

Outdoor sensor (grey)

9:

Domestic hot water flow switch (grey)

10:

Main circuit flow switch (grey)

11:

Under floor heating thermostat (grey)

12:

Flow sensor (grey)

13:

Heating sensor (grey)

14:

Domestic hot water sensor (grey)

15:

Not used: under floor heating

16:

Outdoor sensor (grey)

C7 = EQUIPMENT CONNECTIONS
1:

Secondary output (optional)

2:

Gas valve (white)

3:

3-way valve neutral (white)

4:

Pump (white)

5:

Ionisation (black)

6:

Not connected

7:

Ground 

8:

Pump earth (yellow/green)

9:

Secondary output (optional)

10:

Gas valve (brown)

11:

3-way valve (domestic hot water) (brown)

12:

3-way valve (heating) (brown)

13:

Pump (brown)

14:

Not connected

15:

Earth

16:

Gas valve earth (yellow/green)

Содержание eco Genius 24MFFI





























































Отзывы: