Ariston eco Genius 24MFFI Скачать руководство пользователя

Страница: 43 / 60

FAULT FINDING

TABLE

I and II

YES

YES

IS THE

POWER L.E.D. AND

DISPLAY ON?

DOES A STOP CODE

APPEAR ON THE DISPLAY?

POSITION OF THE SUMMER/

WINTER SELECTOR

1. Check the fuses
2. Check the power supply to
the control panel
3. Check/replace the
ON/OFF button
4. Check the connection between
the main and display P.C.B.s
5. Check/replace the
main and display P.C.B.s

PUSH THE ON/OFF

BUTTON TO ON

MAKE SURE THAT:

1. There is sufficient water in the system
2. The gas is turned on
3. The electrical supply is turned on

SUMMER

WINTER

COMFORT

SELECTOR ON/OFF:

green L.E.D. on

YES: COMFORT ON

Flow

temperature

<40

COMFORT

SELECTOR ON/OFF:

green L.E.D. on

Flow

temperature

>50

Flow

temperature

<40

Flow

temperature

>50

NO:

COMFORT OFF

NO:

COMFORT OFF

YES

D.H.W.

IS BEING

DRAWN?

D.H.W.

IS BEING

DRAWN?

YES

MUST

THE TIME CLOCK

AND/OR ROOM THERMOSTAT

BE ACTIVATED?

BUILT-IN

ELECTRONIC

ANTI-FROST DEVICE:

Is there a condition for it to be active?

(- flow temp. < 3

- outdoor temp. < -3

C (outdoor sensor optional)

- Jumper 4 selects the pump

for continuous

operation)

BUILT-IN

ELECTRONIC

ANTI-FROST DEVICE:

Is there a condition for it to be active?

(- flow temp. < 3

- outdoor temp. < -3

C (outdoor sensor optional)

- Jumper 4 selects the pump

for continuous

operation)

THERE IS NO CALL FOR PUMP OPERATION

It is possible to detect and correct any defect by using the standard fault
finding diagrams described in this chapter.

2.1

AULT

INDING

UIDE

LOW

CHARTS

)

Model 24 MFFI

Содержание eco Genius 24MFFI





























































Результаты поиска

Содержание eco Genius 24MFFI

Отзывы:

Похожие инструкции для eco Genius 24MFFI

Бренды по названию

Популярные бренды

Ariston eco Genius 24MFFI, Руководство по установке

Результаты поиска

Содержание eco Genius 24MFFI

Отзывы:

Похожие инструкции для eco Genius 24MFFI

Бренды по названию

Популярные бренды