Ariens 932031 - ST524 Скачать руководство пользователя страница 6 | Manualshive

Страница: 6 / 29

Ariens 932031 - ST524 Скачать руководство пользователя страница 6

2

Ariens

®

932 Series Sno-Thro

®

Rev. 8/97

SECTION 2: SAFETY

S

AFETY

A

LERT

S

YMBOL

This is a safety alert symbol. It means:

• ATTENTION!

• YOUR SAFETY IS INVOLVED!

When you see this symbol:

• BECOME ALERT!

• OBEY ITS MESSAGE!

S

IGNAL

W

ORDS

The safety alert symbol is used with the signal words
DANGER, WARNING and CAUTION and colors to alert
you to safety messages.

They are used in safety decals on the unit and with
proper operation and procedures in this manual. They
alert you to the existence and relative degree of hazards.

Understand the safety message. It contains important
information about personal safety on or near the unit.

DANGER

IMMINENTLY HAZARDOUS SITUATION!

If not

avoided, WILL RESULT in death or serious injury.

WARNING

POTENTIALLY HAZARDOUS SITUATION!

If not

avoided, COULD RESULT in death or serious injury.

CAUTION

POTENTIALLY HAZARDOUS SITUATION!

If not

avoided, MAY RESULT in minor or moderate injury. It
may also be used to alert against unsafe practices.

Notations

NOTE:

General reference information for proper

operation and maintenance practices.

IMPORTANT:

Specific procedures or information

required to prevent damage to unit or attachment.

WARNING

IMPROPER OPERATION

of this unit

can result in death or serious injury.
Before starting engine, follow these
three steps:

1. Read and understand this manual

and all safety decals on unit or
attachment.

2. Clear area of children and people.

3. Clear area of objects that may be

thrown.

P

RACTICES

AND

L

AWS

Practice usual and customary safe working precautions,
for the benefit of yourself and others. Understand and
follow all safety messages. Be alert to unsafe conditions
and the possibility of minor, moderate, or serious injury or
death. Learn applicable rules and laws in your area.

R

EQUIRED

O

PERATOR

T

RAINING

Original purchaser of this unit was instructed by the seller
on safe and proper operation. If unit is to be used by
someone other than original purchaser; loaned, rented or
sold, ALWAYS provide this manual and any needed
safety training before operation.

OL1253

OL1800

OL1350

OL1021

«
...
4
5
6
7
8
...
»

Содержание 932031 - ST524






























Отзывы:

Нет отзывов