manualshive.com logo in svg

Ariens 932031 - ST524, Руководство владельца/оператора, Страница: 14 / 29

Поделиться
Скачать
Ariens 932031 - ST524 Скачать руководство пользователя страница 14

10

Ariens

®

 

932 Series Sno-Thro

®

 Rev. 8/97

Recoil Starter Handle

When pulled, handle will turn engine over.

IMPORTANT:

  DO NOT let handle snap back against

starter.

Discharge Chute

 

DANGER

ROTATING PARTS 

will cause serious injury or death.

NEVER 

reach into discharge chute or housing while

engine is running.

 WARNING

THROWN OBJECTS

 can result in personal injury

and/or property damage.

 ALWAYS 

position Discharge

Chute and Deflector in safe direction and angle before
starting engine. 

DO NOT 

allow anyone in front of unit

during operation. Be familiar with area of operation.

Discharge Chute rotates 220°.

IMPORTANT:

  If Chute does not stay in

set position, adjust as directed in
Adjustment Section, or repair before
operation.

Chute Crank Handle

Rotate the Chute with Discharge Chute Crank Handle.

IMPORTANT: 

DO NOT force frozen Chute controls.

Start engine and run for 3-5 minutes to thaw. If still
frozen, take to warm place until controls are free.

Discharge Chute Deflector

 CAUTION

THROWN OBJECTS

 can result in personal injury

and/or property damage.

 DO NOT

 throw snow any

higher than necessary.

Place Deflector into position at desired height before
operation.

Push Deflector handle forward to adjust Deflector
downward. Push Deflector Handle downward to adjust
Deflector upward.

IMPORTANT:

  If Chute Deflector does not stay in set

position, adjust as directed in Adjustment Section, or
repair before operation.

Scraper Blade

IMPORTANT: 

 DO NOT allow Scraper Blade to wear or

Auger / Impeller housing will become damaged.

Throttle

The Throttle controls the engine speed. To increase or
decrease the engine speed position control by adjusting
to:

1. "Fast" (normal or warm starts)

2. "Part-Throttle" (cold weather starts)

3. "Slow"

4. "Stop" (engine is off)

Speed Selector

 WARNING

LOSS OF CONTROL 

could result in death or serious

injury. 

DO NOT 

operate at high transport speeds on

slippery surfaces. 

ALWAYS

 use care when backing.

 CAUTION

OVER-SPEED 

can result in serious injury and/or

damage to the unit . 

DO NOT

 clear snow at too fast a

rate.

VISUAL OBSTRUCTION

 can reduce visibility and

cause an accident. Operate unit only when there is
good visibility and light.

The Speed Selector controls the unit travel in a forward
or reverse direction when positioned in notch of speed.

 Forward:

(6)"Fast"

(5)

(4)

(3)

(2)

(1)"Slow" (Best used for removing deep

or hard packed snow)

Reverse:

(1)"Slow"

(2)"Fast"

IMPORTANT:

  Forward speed can be changed without

de-clutching. DO NOT change motion from forward to
reverse with clutch engaged.

OL2720

OL2072

STOP

OS1190

Содержание 932031 - ST524






























Отзывы:

Нет отзывов