Ariens 932031 - ST524 Скачать руководство пользователя

Страница: 18 / 29

Ariens

932 Series Sno-Thro

Rev. 8/97

Engine Oil Check

The engine crankcase oil should be checked daily or
every 5 hours of operation. Oil level MUST be maintained
in safe operating range on dipstick at all times or engine
damage will result (See Engine Manual).

To check, park unit on a level surface and:

1. Clean all debris away from around oil cap.

2. Remove oil cap and dipstick. Wipe oil off dipstick with

a clean cloth. Replace dipstick until cap bottoms on
tube. Remove dipstick again and observe oil level.
Oil should be at the Full (F) mark.

3. If low, add oil and bring up to the Full (F) mark.

IMPORTANT:

DO NOT over fill. Oil Level must not

exceed Full (F) mark.

4. Replace dipstick and cap. Clean up any spilled oil.

Engine Oil Change

Change oil after first 5 hours of operation, thereafter
change oil every 25 hours (more often if required).

NOTE:

Run engine just prior to changing oil. Warm oil

will flow more freely and carry away more contamination.

1. Drain crankcase by removing oil drain plug (see

Engine Manual).

2. When oil has drained replace plug and refill engine

crankcase with new oil of proper grade.

3. Recheck oil level with dipstick.

TTACHMENT

RIVE

ELT

WARNING

IMPROPER ADJUSTMENT

could result in death or

serious injury.

IMPELLER BRAKE MUST

DISENGAGE

when clutch is engaged. Brake must be

at least 1/16" (1,6 mm) to 1/8" (3,2 mm) minimum from
belt when disengaged.

BELT FINGERS

MUST BE between 1/16 to 1/8” from

belt with attachment clutch engaged or belt grabbing
may occur causing impeller to rotate while attachment
clutch is disengaged.

For Attachment Drive Belt Replacement:

1. Shut off engine and allow to cool completely.

Engine Oil Type

Ambient Temperature

SAE 5W30

Below 32

F (0

SAE 30

Above 32

F (0

Figure 4

OS0800

1. Housing Bolt Holes
2. Belt Cover
3. Chute Crank
4. Hair Pin

Figure 5

OS0460

1. Attachment Belt Idler
2. Belt Finger
3. Attachment Drive Belt
4. Traction Drive Belt
5. Traction Belt Idler
6. Engine Pulleys
7. Sheaves

5. Pinion and Gear
6. Chute Strap
7. Cap Screws

Содержание 932031 - ST524






























Результаты поиска

Содержание 932031 - ST524

Отзывы:

Похожие инструкции для 932031 - ST524

Бренды по названию

Популярные бренды

Ariens 932031 - ST524, Руководство владельца/оператора

Результаты поиска

Содержание 932031 - ST524

Отзывы:

Похожие инструкции для 932031 - ST524

Бренды по названию

Популярные бренды