Ariens 932031 - ST524 Скачать руководство пользователя страница 21 | Manualshive

Страница: 21 / 29

Ariens 932031 - ST524 Скачать руководство пользователя страница 21

Rev. 8/97

Ariens

®

932 Series Sno-Thro

®

17

2. Add lubricant, if required, allow oil to drain to level of

plug and replace plug (Figure 9).

3. Use only Ariens special gear lube L-2 (Part Number

00008000).

L

UBRICATION

L

OCATIONS

WARNING

HOT SURFACES

can result in death or

serious injury.

DO NOT

touch parts

which are hot from operation.

ALWAYS

allow parts to cool.

IMPORTANT:

Wipe each fitting clean before and after

lubrication.

IMPORTANT:

DO NOT allow grease or oil to get on

friction wheel, drive disc or belts.

Apply

Hi-Temp Grease or equivalent to the

lube fittings. Order P/N: 00036800 - Three Pack of 3 oz.
cartridges or 00036700 - 10 pack of 14 oz. cartridges.

Apply oil at lubrication points.

Unit should be lubricated at beginning of season or every
25 operating hours (Figure 10). See Maintenance
Schedule.

NOTE:

To grease auger shaft, remove shear bolt nuts,

and shear bolts. Turn auger on shaft while applying
grease at zerk fittings. Replace shear bolt per instructions
in Shear Bolt Replacement.

OL0100

Figure 9

OS0620

1

2

3

1. Auger Gearcase - Cast Iron
2. Oil Fill and Drain level plug
3. Ariens Special L-2 Gear Lube

Figure 10

OS1370

1. Discharge Chute

Base

2. Auger and Shaft
3. Wheel Drive

Spring Package

4. Hex Shaft
5. Bearing Flange

Pin

6. Bushing

Level

2

2

2

2

3

4

6

5

1

«
...
19
20
21
22
23
...
»

Содержание 932031 - ST524






























Отзывы:

Нет отзывов