Ariens 932031 - ST524 Скачать руководство пользователя | Manualshive

Страница: 25 / 29

background image

Rev. 8/97

Ariens

®

932 Series Sno-Thro

®

21

Fasteners

Clutch

Disengagement

Engine Oil

Auger Gearcase

for Leakage

Tire Pressure

General Lubrication

Replace Engine Oil

Clean Cooling Fins

Service Performed

5

Intervals

25

Yearly

Daily

M

AINTENANCE

S

CHEDULE

S

ERVICE

M

ANUAL

Service manuals are available for owners who wish to
perform some of their own maintenance and service.
When ordering manuals or parts, always include the
Models and Serial number of your unit.

Mail requests to:

Ariens Service
655 West Ryan Street
PO Box 157
Brillion, WI 54110-0157

A

TTACHMENTS

See your authorized Ariens dealer to add this additional
attachment to your Sno-Thro.

832007 ....... Brush Attachment

832008 ....... Tiller

A

CCESSORIES

See your authorized Ariens dealer to add the additional
accessories available to your Sno-Thro.

Accessories:

71099700 ... Slicer Bar

72200600 ... 120 Volt Starter Kit (932031)

72403500 ... 120 Volt Starter Kit (932032)

Be sure to always use genuine Ariens parts to keep your
Sno-Thro running like new.

Check if Key Switch is in run position.
Check for electrical problems.
Solenoid not functioning.

Fuel tank is empty.
Ignition switch in Off position.
Build up of dirt and residue around
governor/carburetor.
Check for electrical problems.
Check for engine ignition problems -
See Engine Manufacturer's Service
Manual.

Wrong carburetor adjustment.
Mechanical jam in blower rake or
impeller.
Check spark.
Check fuel supply. Use only clean fuel.

See Engine Manufacturer's Service
Manual.

Friction drive wheel is not adjusted
properly.
Drive belt is not functioning.

Probable Cause

T

ROUBLE

S

HOOTING

Problem

Engine will not crank

Engine will not start

Engine stops

Engine power, noise, idle
and shut down

Does not operate in
Forward/Reverse

OS0751

OS1150

M

AINTENANCE

S

CHEDULE

The chart below shows the recommended maintenance
schedule that should be performed on a regular basis.
More frequent service may be required due to working
conditions (heavy loads, high ambient temperatures,
dusty conditions, or airborne debris).

See Engine Manuals for further maintenance and trouble
shooting information.

«
...
23
24
25
26
27
...
»

Содержание 932031 - ST524






























Отзывы:

Нет отзывов

Похожие инструкции для 932031 - ST524

Бренд: Ozito Страницы: 22

Бренд: Nortrac Страницы: 7

Бренд: Yard force Страницы: 14

SWEEP-N-CLEAN SW48-M

Бренд: T.I.P. Страницы: 33

Бренд: WARRIOR Страницы: 33

Бренд: Stihl Страницы: 32

Бренд: SNOWJOE Страницы: 20

Бренд: Eagle power Страницы: 12

Бренд: Craftsman Страницы: 22

Бренд: Craftsman Страницы: 14

Бренд: Craftsman Страницы: 32

Бренд: Craftsman Страницы: 22

Бренд: Craftsman Страницы: 16

Бренд: Craftsman Страницы: 28

Бренд: Craftsman Страницы: 23

Бренд: Craftsman Страницы: 12

Бренд: Craftsman Страницы: 11

Бренд: Craftsman Страницы: 20

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды