background image

EN - 32

3. Remove swing gate spacer and slide 

drive plate over so that finger clears stop 
hole in frame and can swing past it 
(Figure 35).

NOTICE: 

The drive plate is detached to 

create space between the drive plate and 
friction disc to remove and reinstall the belt. 

4. Pull idler away from traction drive belt 

and remove belt from idler pulley, engine 
sheave and driven pulley (it may be 
necessary to turn engine pulley using 
recoil starter handle).

5. Install new traction drive belt onto driven 

pulley and engine sheave.

6. Swing drive plate toward friction disc 

until finger lines up with stop hole in 
frame. Slide drive plate over, inserting 
finger into stop hole. Reinstall swing 
gate spacer.

7. Reinstall traction idler spring.

NOTICE: 

Make sure the drive plate assembly 

return spring remains connected to the drive 
plate and the frame. Make sure the swing 
gate pivot bushing is piloted in the pivot hole 
in the frame.

8. Replace attachment drive belt (See 

Install New Attachment Drive Belts

 on 

page 31)

.

FRICTION DISC REPLACEMENT

1. Shut off engine, remove key, disconnect 

spark plug wire and allow unit to cool 
completely.

2. Place unit into service position on a level 

surface.

3. Remove both wheels.
4. Remove bottom cover by removing six 

hex bolts.

5. Disconnect pivot pin from the speed 

selector arm. Save the hardware for 
reinstallation.

6. Remove spring clip nearest drive 

sprocket from hex shaft.

7. Remove left bearing flange from frame.

8. Slide hex shaft to the left to remove 

pinion sprocket and friction disc 
assembly from hex shaft.

NOTICE: 

 Be sure to save washers between 

bearing and speed selector arm for 
reassembly.

9. Remove friction disc assembly from 

frame.

10. Remove three screws holding friction 

disc to carrier bearing. 

11. Remove old friction disc. Put the new 

friction disc in place, cup side to carrier 
bearing.

12. Reinstall three screws onto new friction 

disc and carrier bearing. Torque to 
5 – 6 lbf-ft (6.78 – 8.14 N•m).

13. Insert new friction disc assembly into 

frame. Install washers onto carrier 
bearing and slide into speed selector 
arm.

14. Slide hex shaft through new friction disc 

assembly. Install pinion sprocket onto 
hex shaft and slide shaft into right 
bearing.

Figure 35

1. Swing Gate Spacer
2. Drive Plate Assembly
3. Traction Belt Idler
4. Attachment Drive Belts
5. Traction Drive Belt
6. Engine Sheave
7. Friction Disc
8. Drive Plate Finger
9. Swing Gate Pivot Bushing

2

3

6

1

7

4

8

5

9

Содержание 921029









































Отзывы: