Argus QUICK 100 M Скачать руководство пользователя страница 3 | Manualshive

Страница: 3 / 22

Argus QUICK 100 M Скачать руководство пользователя страница 3

INTRODUCTION

14.147.B_QUICK100M en.SM.V1.00.doc

ARGUS Medical AG 11.08.04 / PJ

3 / 22

1. INTRODUCTION

1.1. General

IMPORTANT!

This service manual is intended for the exclusive use of authorized persons who
have been trained by ARGUS Medical AG in the maintenance and repair of the
QUICK

®

100 M docking station.

The service manual is meant to be used together with the user manual

.

IMPORTANT!

ARGUS Medical AG shall not assume any responsibility for any manipulations
which have been carried out on the QUICK

®

100 M docking station by a non-

authorized person.

IMPORTANT!

The QUICK

®

100 M docking station may only be used with the ARGUS 600 D

Software V1.5X and/or ARGUS 414 D Software V1.3X, and/or ARGUS 707,
ARGUS 708 Software V1.XX.

IMPORTANT!

The reading of the barcode (medicament name and infusion data's on a syringe or
a fluid bag) and the data transfer to the pump are fail save. The data transfer from
the QUICK

®

100 M docking station to a PC is

not

fail safe.

This manual contains the latest data available. It is subject to further modifications
in accordance with technical improvements.

«
1
2
3
4
5
...
»

Содержание QUICK 100 M























Отзывы:

Нет отзывов