manualshive.com logo in svg

Argus QUICK 100 M, Руководство по обслуживанию, Страница: 22 / 22

Поделиться
Скачать
Argus QUICK 100 M Скачать руководство пользователя страница 22

 

 

SAFETY STANDARD CHECK 

14.147.B_QUICK100M en.SM.V1.00.doc 

ARGUS Medical AG 11.08.04 / PJ 

22 / 22 

11. SAFETY STANDARD CHECK 

 

Safety standard check

QUICK® 100 M

ARGUS Medical AG

Serial-No.:

Hospital/Dept/Customer:

The safety standard check has to be performed at least every 24 months or after 10000 hours of operation.
The check has to be done in accordance to the operation and service manual.

1 Visual check for damage, cleanness and completeness:

- Housing, labels, accessories, connectors, cables, etc..?

2 Plug in the mains of the docking station

- The green LED on the docking station lights up?

3 Check each docking position with a switched 

off

 pump:

- Mechanical locking and unlocking ok ?
- After docking the pump, its green power LED lights up?

4 Check each docking position with a switched 

on

 pump:

- Buzzer sounds twice, ok?
- LED on docking station flashes orange-red, ok?

5 Chech the external connections:

- Computer interface ?
- Barcode reader interface ?
- Staff alerting system ?

6 Electrical test according to EN60601-1:

- Measurements attached?

Do not install any pump!

All measurements made with a 2.5 m power cord 

 

Содержание QUICK 100 M























Отзывы:

Нет отзывов