manualshive.com logo in svg

Argus green stream 707, Руководство по обслуживанию, Страница: 20 / 38

Поделиться
Скачать
Argus green stream 707 Скачать руководство пользователя страница 20

 

MAINTENANCE 

14.164.A_A707en.SM.V1.01.doc 

ARGUS Medical AG 10.02.04 AS 

20 / 38 

 

 

2. Restart a 

pressure 
build-up.  
 
Check for 
the pressure 
gauge dis-
play which 
must in-
crease. 

 

4.  Press the "MODE" key. 

The display shows “CAL. 
1.4b”. Follow the instruc-
tions on the next side. 

 

1.  Simulate a downstream occlusion by the 3-way 

stop cock.  
The pump must generate a pressure of at least 1.4 
bar. Otherwise there might be a mechanical prob-
lem (pressure plate, door hinge, peristaltic, etc.). 

 

Release the pressure again. 

 

3.  Press the "START / STOP" key 

when a pressure of 0.4 bar has been 
reached. The stored value will be 
acknowledged by a sound. 

 

5.3.5.

 

Calibrating the downstream sensor (right side). 

 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 

Remark: 
By pressing the key "1" the pump display changes to “Pr S xxxx” where the right 
display shows the actual downstream pressure sensor signal in mV. 
Return to the original state by pressing the key "1" again. 

 

Содержание green stream 707







































Отзывы:

Нет отзывов