manualshive.com logo in svg

Argus green stream 707, Руководство по обслуживанию, Страница: 15 / 38

Поделиться
Скачать
Argus green stream 707 Скачать руководство пользователя страница 15

 

CONFIGURATION AND HISTORY PRINTOUT 

14.164.A_A707en.SM.V1.01.doc 

ARGUS Medical AG 10.02.04 AS 

15 / 38 

3.4.4.

 

History printout example 

 
 

/***** History *****/                          Tue 20-Jan-2004 19:40:30 

 

 

Pump type         : ARGUS707 

 

Inventory number  : 005 8 407 

 

Software release  : V1.00  (031218-75C2) 

 

Infused sum       : 388ml 

 

Operating time    : 24h44min 

 

Last service date :  

 
 Pump 

off 

 

Rate   = 0040.0ml/h     Inf-Set = 1            Tue 20-Jan-2004 18:29:22 

 

Total  = 0000.0ml       PrLimit = 0700mbar 

 

Infsum = 0000.0ml       Status  = 0x0000 

 

 Pump 

on 

 

Rate   = 0040.0ml/h     Inf-Set = 1            Tue 20-Jan-2003 18:27:18 

 

Total  = 0000.0ml       PrLimit = 0700mbar 

 

Infsum = 0000.0ml       Status  = 0x0000 

 

3.4.5.

 

History messages 

 

Possible messages appearing in the first line of each history event: 

 

 

No information available 
Battery defective 
Battery low pre alarm 
Battery low, pump stop 

Bolus start 
Bolus stop 
External power off 
External power on 
Downstream occlusion, pump stop 

PrLimit change 

Pump has detected failure 
Pump off 
Pump on 
Pump start 

Pump stop (KVO) 
Rate change 

Enter setup mode 
No drops, pump stop 

Not enough drops, pump stop 
Too many drops, pump stop 
Door open, pump stop 
Inf-Set change 

Timer alarm, pump stop (KVO) 
Total volume reached, pump stop (KVO) 
Data lock off 
Data lock on 
Infsum cleared 

Transport off 

Transport on 
Air bubble, pump stop 
Bolus total reached 
Exit setup mode  

PC configuration done 
PC configuration failure 

Pump start, ext. changed parameters 
Upstream occlusion, pump stop

 

 

Содержание green stream 707







































Отзывы:

Нет отзывов