manualshive.com logo in svg

Arctic Cat ZR 120, Руководство по обслуживанию

Поделиться
Скачать
Arctic Cat ZR 120 Скачать руководство пользователя страница 36

35

1. Open the hood; then disconnect the handlebar

warmer two-wire connector.

2. Connect one ohmmeter lead to the green/white lead;

then connect the other ohmmeter lead to the yellow

lead.

YM-143A

3. The meter must read 14.4 ± 10% ohms.

4. Replace any element measuring less than or more

than the specified amount.

5. Repeat test for the other element; then connect the

leads. Close and latch the hood.

Testing Handlebar Warmer 

Switch

1. Open the hood; then disconnect the main harness

wires from the switch.

2. With the handwarmer toggle in the OFF position,

connect one ohmmeter lead to pin and the other ohm-

meter lead to pin. The meter must read 1 ohm or less

resistance.

YM-145

3. With the handwarmer toggle in the ON position, con-

nect one ohmmeter lead to pin and the other ohmme-

ter lead to pin. The meter must read 1 ohm or less

resistance.

4. Connect the green/white wire to the bottom terminal

and the brown wire to the top terminal on the switch.

YM-144

Содержание ZR 120































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды