Arctic Cat M 1100 Turbo страница 49 Скачать руководство пользователя | Manualshive

Страница: 49 / 68

background image

45

Also, new drive belts have a break-in

period of approximately 25 miles. After

installing a new drive belt, drive the

snowmobile for 25 miles at 3/4 throttle or

less. By revving the engine up and down

(but not exceeding 60 mph), the exposed

cord on the side of a new belt will be

worn down. This allows the drive belt to

gain its optimum flexibility and will

extend drive belt life.

Checking/Adjusting Drive

Belt Deflection

0746-092

The drive belt must have the proper fit in

the drive clutch and driven pulley. To

check for proper drive belt fit, use the

following procedure.

1. Place a straightedge on the top of the

drive belt. The straightedge should

reach from the drive clutch to the top

of the driven pulley.



NOTE: Make sure the drive belt is

all the way out in the driven pulley
before checking drive belt deflection.

2. Using a stiff ruler centered between

the drive clutch and driven pulley,

push down on the drive belt just

enough to remove all slack and note

the amount of deflection. The deflec-

tion should be within the range of

28.5-31.8 mm (1 1/8-1 1/4 in.).

3. To correct drive belt deflection,

remove the sheave adjuster from the

pulley, remove or add shim washers

to the adjuster, and install the

adjuster.



NOTE: Adding shim washers will

decrease belt deflection and remov-
ing shim washers will increase belt
deflection. Available shim washers
from Arctic Cat are p/n 0648-714
(0.090 in.) - one included in the tool
kit, p/n 0648-715 (0.030 in.), and p/n
0648-716 (0.060 in.).



NOTE: Removing/adding shim

washers may be done by the snow-
mobile owner if qualified to do so. If
the owner does not feel qualified,
take the snowmobile to an autho-
rized Arctic Cat Snowmobile dealer
for this service. This service is at the
discretion and expense of the snow-
mobile owner.

Removing Drive Belt



NOTE: Changing a drive belt can

be done by the snowmobile owner if
qualified to do so. If the owner does
not feel qualified, take the snowmo-
bile to an authorized Arctic Cat
Snowmobile dealer for this service.
This service is at the discretion and
expense of the snowmobile owner.

1. Turn ignition key to the OFF posi-

tion and wait for all moving parts to

stop.

2. Set the brake lever lock.
3. Open the left-side access panel; then

remove the rear belt guard.



NOTE: On the 1100 cc models,

move and secure the rear belt guard
up and out of the way.

4. Remove the cap screw, lock washer,

washer, and sheave adjuster from the

end of the driven pulley; then

remove the sheave adjuster from the

cap screw.

0743-395

CAUTION

Never run the engine with the drive
belt removed. Excessive revving of the
engine could result in serious engine
damage and drive clutch failure.

«
...
47
48
49
50
51
...
»

Содержание M 1100 Turbo





































































Отзывы:

Нет отзывов

Похожие инструкции для M 1100 Turbo

Бренд: Crown Страницы: 1

4-Way Electronic Crossover

Бренд: Radio Shack Страницы: 8

Бренд: Apogee Страницы: 11

Бренд: Art Страницы: 12

Бренд: Art Страницы: 12

Бренд: Audio System Страницы: 2

GERMAN SOUND FWX 3-WAY

Бренд: Audio System Страницы: 4

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды