Arctic Cat M 1100 Turbo Скачать руководство пользователя | Manualshive

Страница: 18 / 68

background image

14

0745-848

2. Adjust the handlebar to operator’s

desired position, tighten the cap

screws evenly to 15 ft-lb, and check

steering for maximum right/left

turning capabilities.



NOTE: Do not rotate the handlebar

to a position that allows air to enter
the brake system.

Speedometer/

Tachometer Angle

The speedometer/tachometer can be

adjusted to the operator’s desired posi-

tion. To adjust, use the following proce-

dure.

1. Loosen the lock nuts and cap screws

on each side of the speedometer/

tachometer bracket.

2. Adjust the speedometer/tachometer

to the desired angle; then tighten the

lock nuts securely.

Exhaust System

The exhaust system is designed to reduce

noise and to improve the total perfor-

mance of the engine. If any exhaust sys-

tem component is removed from the

engine and the engine is run, severe

engine damage will result.

Air-Intake Silencer

Used in conjunction with the fuel intake

system is a specially designed air-intake

silencer. The purpose of the silencer is to

quiet the intake of fresh air. Since the fuel

intake system is calibrated with the air-

intake silencer in place, the engine must

never be run with the silencer removed.

Performance will not be improved if the

air-intake silencer is removed. In con-

trast, severe engine damage will occur.

Cooling System

These snowmobiles are equipped with a

closed liquid cooling system for engine

cooling. The cooling system should be

inspected daily for leakage and damage.

Also, the coolant level should be checked

daily. If leakage or damage is detected,

take the snowmobile to an authorized

Arctic Cat Snowmobile dealer for ser-

vice. If not under warranty, this service is

at the discretion and expense of the

snowmobile owner.
When filling the cooling system reser-

voir, use an ethylene glycol-based cool-

ant/water mixture which will satisfy the

coldest anticipated weather conditions of

your area in accordance with the coolant

manufacturer’s recommendations.



NOTE: On the HCR models if oper-

ating on ice or hard-packed snow,
the ice scratchers must be engaged
to reduce engine overheating.

For checking/filling cooling system, refer

to Coolant Level sub-section in the Main-

tenance section.

Battery

(Electric Start)

It is extremely important that the battery

be maintained at full charge at all times

and that the battery connections be clean

and tight. If charging the battery becomes

necessary, refer to Battery sub-section in

the Maintenance section.

! WARNING

Tighten cap screws according to
specifications to prevent unexpected
“movement” of the handlebar during
operation over rough terrain. DO NOT
position the handlebar so steering
(maximum right/left turning capabili-
ties) or throttle and brake controls
are affected.

CAUTION

These snowmobiles are not designed
to be operated in dusty conditions.
Operating the snowmobile in dusty
conditions will result in severe
engine damage.

«
...
16
17
18
19
20
...
»

Содержание M 1100 Turbo





































































Отзывы:

Нет отзывов

Похожие инструкции для M 1100 Turbo

Бренд: Rane Страницы: 5

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды