Arcteq AQ-F213 Скачать руководство пользователя страница 412

Страница: 412 / 455

The RTD input module is an add-on module with eight (8) RTD input channels. Each input supports

2-wire, 3-wire and 4-wire RTD sensors as well as thermocouple (TC) sensors. The sensor type can be

selected with software for two groups, four channels each. The supported sensor types are as follows:

• Supported RTD sensors: Pt100, Pt1000
• Supported thermocouple sensors: type K (NiCh/NiAl), type J (Fe/constantan), type T (Cu/

constantan) and type S (Cu/CuNi compensating).

Figure. 8.8 - 250. Different sensor types and their connections.

8.9 Serial RS-232 communication module (optional)

Figure. 8.9 - 251. Serial RS-232 module connectors.

Q-F213

-F213

Instruction manual

Version: 2.04

411

Содержание AQ-F213







































































































































































































































































































































































































































































Результаты поиска

Содержание AQ-F213

Отзывы:

Бренды по названию

Популярные бренды

Arcteq AQ-F213, Инструкция по эксплуатации

Результаты поиска

Содержание AQ-F213

Отзывы:

Бренды по названию

Популярные бренды