Arcteq AQ-F213 Скачать руководство пользователя страница 323

Страница: 323 / 455

Name

Range

Step

Default

Description

Input value

-10

…10

0.001

The second input point in the mA output control curve.

Scaled mA

output

value 2

0.0000…24.0000mA 0.0001mA 0mA

The mA output value when the measured value is equal

to or greater than Input value 2.

Figure. 5.4.7 - 202. Example of the effects of mA output channel settings.

Table. 5.4.7 - 209. Hardware indications.

Name

Range Step

Description

Hardware in mA output channels 1...4 0: None

1: Slot A

2: Slot B

3: Slot C

4: Slot D

5: Slot E

6: Slot F

Indicates the option card slot where the mA output card is located.

Hardware in mA output channels 5...8

Table. 5.4.7 - 210. Measurement values reported by mA output cards.

Name

Range

Step

Description

mA in Channel 1

0.0000…24.0000mA 0.0001mA Displays the measured mA value of the selected input

channel.

mA in Channel 2

mA Out Channel Input

Magnitude now

-10

…10

0.001

Displays the input value of the selected mA output

channel at that moment.

mA Out Channel Outputs

now

0.0000…24.0000mA 0.0001mA Displays the output value of the selected mA output

channel at that moment.

5.4.8 Vector jump (Δφ; 78)

Distribution systems may include different kinds of distributed power generation sources, such as wind

farms and diesel or fuel generators. When a fault occurs in the distribution system, it is usually detected

and isolated by the protection system closest to the faulty point, resulting in the electrical power system

shutting dow either partially or completely. The remaining distributed generators try to deliver the

power to the part of the distribution system that has been disconnected from the grid, and usually an

overload condition can be expected. Under such overload conditions, it is normal to have a drop in

voltage and frequency. This overload results in the final system disconnection from the islanding

generator(s). The disconnection depends greatly on the ratio between the power generation and the

demand of the islanded system. When any power is supplied to a load only from distributed generators,

(due to the opening of the main switch), the situation is called an isolated island operation or an

islanded operation of the electrical distribution network.

Q-F213

-F213

Instruction manual

Version: 2.04

322

Содержание AQ-F213







































































































































































































































































































































































































































































Результаты поиска

Содержание AQ-F213

Отзывы:

Бренды по названию

Популярные бренды

Arcteq AQ-F213, Инструкция по эксплуатации

Результаты поиска

Содержание AQ-F213

Отзывы:

Бренды по названию

Популярные бренды